Acer Aspire 5930/5930Z/5730Z Series Service Guide

key, remove, dimm, error, model, cable, card, setup, cover, check, disk, pack, utility, hdd, ath, usb, boot, computer and item

Aspire 5930/5930Z/5730Z Series

Service Guide

Service guide files and updates are available

on the ACER/CSD web; for more information,

please refer to http://csd.acer.com.tw

PRINTED IN TAIWAN

Revision History

Please refer to the table below for the updates made on Aspire 5930/5930Z/5730Z Series service guide.

Date

Chapter

Updates

transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without

the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice.

Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular

purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the

programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its

dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential

damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

III

Conventions

The following conventions are used in this manual:

SCREEN MESSAGES

Denotes actual messages that appear

on screen.

NOTE

Gives bits and pieces of additional

information related to the current

topic.

WARNING

Alerts you to any damage that might

result from doing or not doing specific

actions.

CAUTION

Gives precautionary measures to

avoid possible hardware or software

problems.

IMPORTANT

Reminds you to do specific actions

relevant to the accomplishment of

procedures.

Preface

Before using this information and the product it supports, please read the following general information.

This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION

decided for Acer's "global" product offering. To better fit local market requirements and enhance product

competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.

add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered

in this generic service guide. In such cases, please contact your regional offices or the responsible

personnel/channel to provide you with further technical details.

Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information

available on your regional web or channel. If, for whatever reason, a part number change is made, it will

not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer

office may have a DIFFERENT part number code to those given in the FRU list of this printed Service

Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and

service of customer machines.

Table of Contents

System Specifications

Features

System Block Diagram

Your Acer Notebook tour

Right View

Indicators

Easy-Launch Buttons

Touchpad Basics (with fingerprint reader)

Touchpad basics (with two-click buttons)

Using the Keyboard

Lock Keys and embedded numeric keypad

Windows Keys

Hot Keys

Special Key (only for certain models)

Acer Empowering Technology

Launching Acer Empowering Technology

Empowering Technology password

Acer eAudio Management (only for certain models)

Acer ePower Management

Acer eDataSecurity Management (only for certain models)

Acer eRecovery Management

Acer eSettings Management

Windows Mobility Center

Using the System Utilities

Acer GridVista (dual-display compatible)

Hardware Specifications and Configurations

System Utilities

BIOS Setup Utility

Navigating the BIOS Utility

Information

Main

Security

Intel

Boot

Exit

BIOS Flash Utility

Remove HDD/BIOS Utility

Machine Disassembly and Replacement

Disassembly Requirements

General Information

Pre-disassembly Instructions

Disassembly Process

External Module Disassembly Process

External Modules Disassembly Flowchart

Removing the Battery Pack

Removing the SD dummy card

Removing the ExpressCard dummy card

Removing the Lower Cover

Removing the DIMM

Removing the WLAN Board Modules

Removing the TV Tuner Board Modules

Removing the Modem Board

VII

Table of Contents

Removing the Hard Disk Drive Module

Removing the Optical Drive Module

Main Unit Disassembly Process

Main Unit Disassembly Flowchart

Removing the Keyboard

Removing the Middle Cover

Removing the Power Board

Removing the Heatsink Fan Module

Removing the CPU and VGA Heatsink Module

Removing the CPU

Removing the VGA Board (Discrete Model only)

Removing the LCD Module

Separating the Upper Case from the Lower Case

Removing the Media Board

Removing the E-key Board

Removing the Speaker Module

Removing the Launch Board

Removing the Fingerprint and Touchpad Module

Removing the Main Board

Removing the USB Board Module

Removing the Audio Board Module

Removing the Subwoofer and the Bluetooth Modules

100

LCD Module Disassembly Process

102

LCD Module Disassembly Flowchart

102

Removing the LCD Bezel

103

Removing the LCD module with the Brackets

104

Removing the FPC Cable

106

Removing the LCD Brackets

107

Removing the Antennas

108

Removing the Web Camera

109

Troubleshooting

111

System Check Procedures

112

External Diskette Drive Check

112

External CD-ROM Drive Check

112

Keyboard or Auxiliary Input Device Check

112

Memory check

113

Power System Check

113

Touchpad Check

115

Power-On Self-Test (POST) Error Message

116

Index of Error Messages

117

Phoenix BIOS Beep Codes

120

Index of Symptom-to-FRU Error Message

125

Intermittent Problems

129

Undetermined Problems

130

Jumper and Connector Locations

131

Top and Bottom View

131

Clearing Password Check and BIOS Recovery

133

Clearing Password Check

133

BIOS Recovery by Crisis Disk

134

FRU (Field Replaceable Unit) List

135

Aspire 5930/5930Z/5730Z Series Exploded Diagram

136

Aspire 5930/5930Z/5730Z Series

146

VIII

Table of Contents

Model Definition and Configuration

146

Test Compatible Components

169

Microsoft® Windows® Vista Environment Test

170

Online Support Information

173

Index

175

Table of Contents

Chapter 1

System Specifications

Features

Below is a brief summary of the computer’s many feature:

Platform

Intel® Centrino® 2 processor technology, featuring:

Intel® Core™2 Duo processor

Mobile Intel® PM45/GM45 Express Chipset*

Intel® Wireless WiFi Link 5100/5300*, 5150/5350 (Subject to availability)

Intel® Pentium® Core processor*

Mobile Intel® GM45 Express Chipset*

Acer InviLink™ Nplify™ 802.11b/g/Draft-N*

Acer InviLink™ 802.11b/g*

System Memory

Dual-Channel DDR2 SDRAM support

Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules*

Display and graphics

15.4" WXGA 1280 x 800

Mobile Intel® GM45 Express Chipset (Intel® GMA X4500HD)*

NVIDIA® GeForce® 9300M GS/9600M GT*

Digital TV-tuner supporting DVB-T*

Storage subsystem

2.5" hard disk drives

Optical drive options:

Blu-ray Disc™/DVD-Super Multi double-layer drive

DVD-Super Multi double-layer drive

5-in-1 card reader

Special keys and controls

88-/89-/93-key keyboard

Touchpad pointing device

Empowering Key

Easy-launch buttons: WLAN, Internet, email, Bluetooth, Acer Arcade™

Acer MediaTouch keys: play/pause, stop, previous, next

Volume wheel

Acer Media Center remote control*

Chapter 1

Audio

Dolby®-certified surround sound system with two built-in stereo speakers and one subwoofer

supporting low-frequency effects

S/PDIF (Sony/Philips Digital Interface) support for digital speakers

Acer PureZone technology with two built-in stereo microphones

Communication

Acer Video Conference, featuring:

Integrated Acer Crystal Eye webcam

Acer Video Conference Manager software

Acer PureZone technology

Optional Acer Xpress VoIP phone

WLAN:

Intel® Wireless WiFi Link 5100/5300*

Acer InviLink™ Nplify™ 802.11b/g/Draft-N*

Acer InviLink™ 802.11b/g*

WiFIi®/WiMAX™: Intel® Wireless WiFi Link 5150/5350 (Subject to availability)

WPAN: Bluetooth® 2.0+EDR (Enhanced Data Rate)

LAN: Gigabit Ethernet; Wake-on-LAN ready

Modem: 56K ITU V.92

I/O Ports

Acer EasyPort IV connector

(for Aspire 5930 series only)

ExpressCard™/54 slot

5-in-1 card reader (SD/MMC/MS/MS PRO/xD)

4 USB 2.0 ports

HDMI™ port with HDCP support*

USB 2.0/ eSATA port *

NOTE: If you plug an eSATA device you will have three USB ports available in the mean time.

Consumer infrared (CIR) port

External display (VGA) port

RF-in jack (for Aspire 5930 series only)

Headphones/speaker/line-out jack with S/PDIF support*

Microphone-in jack

Line-in jack

Ethernet (RJ-45) port

Modem (RJ-11) port

DC-in jack for AC adapter

Environment

Temperature:

Operating: 5 °C to 35 °C

Non-operating: -20 °C to 65 °C

Humidity (non-condensing):

Operating: 20% to 80%

Chapter 1

Non-operating: 20% to 80%

NOTE: "*" "Only for certain models"

NOTE: The specifications listed above are for reference only. The exact configuration of your PC depends on

the model purchased.

Chapter 1

System Block Diagram

Chapter 1

Your Acer Notebook tour

After knowing your computer features, let us show you around your new computer.

Front View

Icon

Item

Description

Acer PureZone

Two internal stereo microphones for sound recording.

Acer Crystal Eye

Web camera for video communication.

Display screen

Also called Liquid-Crystal Display (LCD), displays computer

output.

Power button

Turns the computer on and off.

Speakers

Left and right speakers deliver stereo audio output.

Easy-launch

Buttons for launching frequently used programs.

buttons

Keyboard

For entering data into your computer.

Palmrest

Comfortable support area for your hands when you use the

computer.

Chapter 1

Icon

Item

Description

Touchpad

Touch-sensitive pointing device which functions like a computer

mouse.

Click buttons (left,

The left and right buttons function like the left and right mouse

center* and right)

buttons. *The center button serves as Acer Bio-Protection

fingerprint reader supporting Acer FingerNav 4-way control

function (only for certain models).

11/12

Status indicators

Light-Emitting Diodes (LEDs) that light up to show the status of

the computer's functions and components.

Empowering key

Launch Acer Empowering Technology

Acer MediaTouch

For use with Acer Arcade and other media playing programs.

keys

Chapter 1

Closed Front View

Icon

Item

Description

USB 2.0 ports

Connect to USB 2.0 devices (e.g., USB mouse, USB

camera) (only for certain models).

Unlimited volume

Adjust the volume of the audio-out.

control wheel

CIR receiver

Receives signals from a remote control.

Latch

Locks and releases the lid.

Speakers

Left and right speakers deliver stereo audio output.

4-pin IEEE 1394

Connects to IEEE 1394 devices.

port

Line-in jack

Accepts audio line-in devices (e.g., audio CD player,

stereo walkman).

Microphone-in

Accepts input from external microphones.

jack

Headphones/

Connects to audio line-out devices (e.g., speakers,

speaker/line-out

headphones).

jack with

S/PDIF support

Bluetooth

Enable/disables the Bluetooth function.

communication

switch

Wireless

Enable/disables the wireless function.

communication

switch

Infrared port

Interfaces with infrared devices (e.g., infrared printer and

IR-aware computer).

Chapter 1

Left View

Icon

Item

Description

Kensington lock slot

Connects to a Kensington-compatible computer security

lock.

Acer EasyPort IV

Connects to Acer EasyPort IV

connector

(for Aspire 5930 series only).

Ethernet (RJ-45)

Connects to an Ethernet 10/100/1000-based network.

port

External display

Connects to a display device

(VGA) port

(e.g., external monitor, LCD projector).

HDMI

Connects to a television or display device with HDMI

input.

USB 2.0/ e SATA

Connects to USB 2.0 or eSATA devices (only for certain

port

models).

Note: If you plug an eSATA device you will have three

USB ports available in the mean time.

5-in-1 card reader

Accepts Secure Digital (SD), MultiMediaCard (MMC),

Memory Stick (MS), Memory Stick PRO (MS PRO), xD-

Picture Card (xD).

ExpressCard/54

Accepts one ExpressCard/54 module.

slot

Right View

Icon

Item

Description

Line-in jack

Accepts audio line-in devices (e.g., audio CD player,

stereo walkman).

Chapter 1

Icon

Item

Description

Microphone-in jack

Accepts input from external microphones.

Headphones/speaker/

Connects to audio line-out devices (e.g., speakers,

line-out jack with

headphones).

S/PDIF support

Optical drive

Internal optical drive; accepts CDs or DVDs.

Optical disk access

Lights up when the optical drive is active.

indicator

Optical drive eject

Ejects the optical disk from the drive.

button

Emergency eject hole

Ejects the optical drive tray when the computer is

turned off.

Note: Insert a paper clip to the emergency eject

hole to eject the optical drive tray when the

computer is off.

USB 2.0 port

Connect to USB 2.0 devices (e.g., USB mouse,

USB camera).

RF-in port

Accepts input signals from digital TV-tuner devices

(for Aspire 5930 series only).

Modem (RJ-11) port

Connects to a phone line.

Chapter 1

Rear View

Icon

Item

Description

DC-in jack

Connects to an AC adapter.

Ventilation slots

Enable the computer to stay cool, even after

prolonged use.

Chapter 1

Bottom View

Icon

Item

Description

Battery bay

Houses the computer's battery pack.

Battery release

Releases the battery for removal.

latch

Battery lock

Locks the battery in position.

Memory

Houses the computer's main memory.

compartment

Hard disk bay

Houses the computer's hard disk (secured with

screws).

Sub woofer

Emits low frequency sound output

(for Aspire 5930 series only).

Ventilation slots

Enable the computer to stay cool, even after

and cooling fan

prolonged use.

Note: Do not cover or obstruct the opening of the

fan.

Chapter 1

Indicators

The computer has several easy-to-read status indicators. The front panel indicators are visible even when the

computer cover is closed.

Icon

Function

Description

HDD

Indicates when the hard disk drive is

active.

Num Lock

Lights up when Num Lock is

activated.

Caps Lock

Lights up when Caps Lock is

activated.

Power

Indicates the computer's power

status.

Battery

Indicates the computer's battery

status.

NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows

green when in AC mode.

Easy-Launch Buttons

Located beside the keyboard are application buttons. These buttons are called easy-launch buttons. They are:

WLAN, Internet, email, Bluetooth, Arcade and Acer Empowering Technology.

The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To

set the Web browser, mail and programmable buttons, run the Acer Launch Manager.You can access the

Launch Manager by clicking on Start, All Programs, and then Launch Manager to start the application.

Icon

Function

Description

Wireless communication

Enables/disables the wireless function. Indicates the status

button/indicator

of wireless LAN communication.

(manufacturing option)

Web browser

Internet browser (user-Programmable)

Mail

Email application (user-Programmable)

Bluetooth communication

Enables/disables the Bluetooth function. Indicates the

button/indicator

status of Bluetooth communication.

(manufacturing option)

Arcade

Launch Acer Arcade utility

(only for certain models).

Acer Empowering

Launch Acer Empowering Technology (user-

Technology

programmable)

Chapter 1

Touchpad Basics (with fingerprint reader)

The following items show you how to use the touchpad with Acer Bio-Protection fingerprint reader.

Move your finger across the touchpad (2) to move the cursor.

Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and execution

functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the

touchpad is the same as clicking the left button.

Use Acer Bio-Protection fingerprint reader (3) supporting Acer FingerNav 4-way control function (only

for certain models) to scroll up or down and move left or right a page. This fingerprint reader or button

mimics your cursor pressing on the right scroll bar of Windows applications.

Function

Left button (1)

Right button (4)

Main touchpad (2)

Center button (3)

Execute

Quickly click

Tap twice (at the same speed

twice.

as double-clicking a mouse

button).

Select

Click once.

Tap once.

Drag

Click and

Tap twice (at the same speed

hold, then

as double-clicking a mouse

use finger on

button); rest your finger on the

the touchpad

touchpad on the second tap

to drag the

and drag the cursor.

cursor.

Access

Click once.

context

Scroll

Swipe up/down/left/right

using Acer FingerNav 4-

way control function

(Manufacturing option).

Touchpad basics (with two-click buttons)

The following items show you how to use the touchpad with two-click buttons.

Move your finger across the touchpad (1) to move the cursor.

Chapter 1

Press the left (2) and right (3) buttons located beneath the touchpad to perform selection and execution

functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the

touchpad is the same as clicking the left button.

Function

Left button (2)

Right button (3)

Main touchpad (1)

Execute

Quickly click twice.

Tap twice (at the same speed as double-clicking

a mouse button).

Select

Click once.

Tap once.

Drag

Click and hold, then use

Tap twice (at the same speed as double-clicking

finger on the touchpad

a mouse button); rest your finger on the touchpad

to drag the cursor.

on the second tap and drag the cursor.

Access

Click once.

context menu

NOTE: Illustrations for reference only. The exact configuration of your PC depends on the model purchased.

NOTE: When using the touchpad, keep it — and your fingers — dry and clean. The touchpad is sensitive to

finger movement; hence, the lighter the touch, the better the response. Tapping harder will not increase

the touchpad's responsiveness.

NOTE: By default, vertical and horizontal scrolling is enabled on your touchpad. It can be disabled under

Mouse settings in Windows Control Panel.

Chapter 1

Using the Keyboard

The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function

and special keys.

Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off.

Lock key

Description

Caps Lock

When Caps Lock is on, all alphabetic characters typed are

in uppercase.

Num Lock

When Num Lock is on, the embedded keypad is in numeric mode. The keys

function as a calculator (complete with the arithmetic operators +, -, *, and /).

Use this mode when you need to do a lot of numeric data entry. A better solution

would be to connect an external keypad.

NOTE: <Fn> + <F11> works only for certain models.

Scroll Lock <Fn> +

When Scroll Lock is on, the screen moves one line up or down when you press

<F12>

the up or down arrow keys respectively. Scroll Lock does not work with some

applications.

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters

located on the upper right corner of the key caps. To simplify the keyboard legend, cursor-control key symbols

are not printed on the keys.

Desired access

Num Lock on

Num Lock off

Number keys on

Type numbers in a normal manner.

embedded keypad

Cursor-control keys on

Hold <Shift> while using cursor-

Hold <Fn> while using cursor-

embedded keypad

control keys.

Main keyboard keys

Hold <Fn> while typing letters on

Type the letters in a normal

embedded keypad.

manner.

Chapter 1

Windows Keys

The keyboard has two keys that perform Windows-specific functions.

Key

Description

Windows

Pressed alone, this key has the same effect as

key

clicking on the Windows Start button; it launches the

Start menu.

It can also be used with other keys to provide a

variety of functions:

>: Open or close the Start menu

> + <D>: Display the desktop

> + <E>: Open Windows Explore

> + <F>: Search for a file or folder

> + <G>: Cycle through Sidebar gadgets

> + <L>: Lock your computer (if you are

connected to a network domain), or switch users (if

you're not connected to a network domain)

> + <M>: Minimizes all windows

> + <R>: Open the Run dialog box

> + <T>: Cycle through programs on the

taskbar

> + <U>: Open Ease of Access Center

> + <X>: Open Windows Mobility Center

> + <BREAK>: Display the System Properties

dialog box

> + <SHIFT+M>: Restore minimized windows

to the desktop

> + <TAB>: Cycle through programs on the

taskbar by using Windows Flip 3-D

> + <SPACEBAR>: Bring all gadgets to the

front and select Windows Sidebar

<CTRL> + <

> + <F>: Search for computers (if

you are on a network)

<CTRL> + <

> + <TAB>: Use the arrow keys to

cycle through programs on the taskbar by using

Windows Flip 3-D

Note: Depending on your edition of Windows Vista,

some shortcuts may not function as described.

Application

This key has the same effect as clicking the right

key

mouse button; it opens the application's context

menu.

Chapter 1

Hot Keys

The computer employs hotkeys or key combinations to access most of the computer’s controls like screen

brightness, volume output and the BIOS utility.

To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.

Hotkey

Icon

Function

Description

Hotkey help

Displays help on hotkeys.

Acer eSettings

Launches Acer eSettings in Acer Empowering

Technology.

Acer ePower

Launches Acer ePower Management in Acer

Management

Empowering Technology.

Sleep

Puts the computer in Sleep mode.

Display toggle

Switches display output between the display

screen, external monitor (if connected) and

both.

Screen blank

Turns the display screen backlight off to save

power. Press any key to return.

Touchpad toggle

Turns the internal touchpad on and off.

Speaker toggle

Turns the speakers on and off.

<Fn> + <

Brightness up

Increases the screen brightness.

<Fn> + <

Brightness down

Decreases the screen brightness.

<Fn> + <

Volume up

Increases the sound volume

(only for certain models).

<Fn> + <

Volume down

Decreases the sound volume

(only for certain models).

Chapter 1

Special Key (only for certain models)

You can locate the Euro symbol and the US dollar sign at the upper-center

and/or bottom-right of your keyboard.

The Euro symbol

Open a text editor or word processor.

Either press <

> at the bottom-right of the keyboard, or hold <Alt Gr> and then press the <5> key at the

upper-center of the keyboard.

NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/

typography/faq/faq12.htm for more information.

The US dollar sign

Open a text editor or word processor.

Either press <

> at the bottom-right of the keyboard, or hold <Shift> and then press the <4> key at the

upper-center of the keyboard.

NOTE: This function varies according to the language settings.

Chapter 1

Acer Empowering Technology

The Empowering Technology toolbar makes it easy for you to access frequently used functions and manage

your new Acer system. Activated by pressing the Empowering Key, it provides access to the following utilities:

NOTE: The following content is for general reference only. Actual product specifications may vary.

Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home

Theater on your system (only for certain models).

Acer ePower Management optimizes battery usage via customizable power plans.

Acer eDataSecurity Management protects data with passwords and encryption (only for certain

models).

Acer eRecovery Management backs up and recovers data flexibly, reliably

and completely.

Acer eSettings Management accesses system information and adjusts settings easily.

For more information, right-click on the Empowering Technology toolbar, then select Help. For help with a

particular utility, launch the utility and click the

icon at the bottom of the active window.

Launching Acer Empowering Technology

To launch Acer Empowering Technology:

Press the Empowering Key to display the Acer Empowering Technology toolbar on the desktop.

To hide the toolbar, press the Empowering Key again or click the hide button

on the toolbar.

You may also launch Acer Empowering Technology by running the program from the Acer Empowering

Technology program group in the Start menu, or by double-clicking the

icon if you have created a

desktop shortcut.

To launch Acer Empowering Technology applications:

On the Acer Empowering Technology toolbar, click the icon that corresponds to the application you want

to launch.

When you mouse over an application icon, a quick menu appears below the toolbar. The quick menu

allows you to perform certain tasks simply and quickly.

You may also run the application by selecting it from the Acer Empowering Technology program group in

the Start menu.

NOTE: You may also double-click or right-click

to run Acer eAudio Management, and right-click

run Acer ePower Management from the system tray.

Chapter 1

Empowering Technology password

You must set the Empowering Technology password to use the password protection feature of Acer

eRecovery Management to protect your data.

To set the Empowering Technology password:

Launch Acer eRecovery Management.

Click the Restore tab.

Click Password settings. The Empowering Technology Password Center dialogue box pops up.

Click Create a new password.

In the Create a New Password dialogue box, key in and confirm your password in the appropriate boxes.

Your password should have a minimum of 4 and a maximum of 12 characters.

Enter a password hint that will help you remember your password.

Make sure the box Use for Acer eRecovery Management is checked.

Click OK to set the password.

Chapter 1

Acer eAudio Management

(only for certain models)

Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home Theater on

your system. Select Movie or Game mode to experience the awesome realism of 5.1-channel audio output

from the speakers fitted to your system via Dolby Surround sound technology. Music mode lets you enjoy your

favorite tunes, in vivid detail.

To choose your playback device, click the

icon on the upper right side of the Acer eAudio Management

window.

Chapter 1

Acer ePower Management

Acer ePower Management features a straightforward user interface for configuring your power management

options. To access this utility, select Acer ePower Management from the Empowering Technology toolbar, run

the program from the Acer Empowering Technology program group in Start menu, or right-click the Windows

power icon in the system tray and select Acer ePower Management.

Using power plans

Acer ePower Management comes with three predefined power plans: Balanced, High performance and

Power saver.

View and adjust settings for On Battery and Plugged In modes by clicking the appropriate tabs. For more

power options, click

in the Acer ePower Management utility, or right-click the Windows power icon in the

system tray and select Power Options.

You can also create customized power plans. You can create, switch between, edit, delete and restore power

plans, as described below.

To create a new power plan:

Creating customized power plans allows you to save and quickly switch to a personalized set of power

options.

Click the New power plan option or icon

Enter a name for your new power plan.

Choose a predefined power plan to base your customized plan on.

If necessary, change the display, sleep and hibernation settings you want your computer to use.

Click OK to save your new power plan.

To switch between power plans:

Move your mouse over the Acer ePower Management

application on the Acer Empowering

Technology toolbar. The quick menu appears.

Select the power plan you want to switch to.

You may also switch between power plans by launching the Acer ePower Management application.

Select the power plan you wish to switch to, then click Apply.

To edit a power plan:

Editing a power plan allows you to adjust system settings like LCD brightness, CPU speed and Graphics

power mode (only for certain models).

Switch to the power plan you wish to edit.

Adjust settings as required.

Click Apply or Save to save your new settings.

NOTE: You can revert to the default settings of the predefined power plans by clicking the Restore button.

To delete a power plan:

You cannot delete the power plan you are currently using. The active power plan will mark with

in upper

left corner of power plan icon. If you want to delete the active power plan, switch to another one first.

Select the power plan you wish to delete.

Click the Delete this plan icon.

NOTE: You cannot delete the predefined power plans, but you can modify the settings of the predefined power

plans.

Chapter 1

Battery status

The quick menu shows the remaining battery life based on current usage.

You can also launch the Acer ePower Management application and refer to the Battery status panel

located just below the power plans.

Click the Battery tab to view remaining battery life, battery status, and remaining battery life in standby

and hibernate modes.

Acer eDataSecurity Management

(only for certain models)

Acer eDataSecurity Management is an encryption utility that protects your files from being accessed by

unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for quick data

encryption/decryption and also supports on-the-fly file encryption for Lotus Notes and Microsoft Outlook.

On first use, the Acer eDataSecurity Management setup wizard will prompt you to create the Master

Password. You will use this password to access the Personal Secure Disk (PSD). The Master Password may

also be used to encrypt/decrypt files by default.

Chapter 1

If you set a different password to encrypt a file, but you forgot the encryption password, you can use the

Master Password to decrypt the file.

NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose

the password, the Master Password is the only other key capable of decrypting the file. If you lose both

passwords, there will be no way to decrypt your encrypted file! Be sure to safeguard all related

passwords!

Acer eRecovery Management

Acer eRecovery Management is a versatile backup utility. It allows you to create full or incremental backups,

burn the factory default image to optical disc, and restore from previously created backups or reinstall

applications and drivers. By default, user-created backups are stored to the D:\ drive.

Acer eRecovery Management provides you with:

Backup:

Chapter 1

Back up factory default to CD/DVD

Back up drivers and applications to CD/DVD

Create user backup

Manage user backups

Restore:

Restore system to factory default

Reinstall applications/drivers

Restore system from user backup

Password settings

To use the password protection feature of Acer eRecovery Management to protect your data, you must first set

the Empowering Technology password. To set the password, refer to the section "Empowering Technology

password".

For more information, please refer to"Acer eRecovery Management" on page 62 in the Acer System

User's Guide.

NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery

Management's Backup factory default to CD/DVD feature to burn a backup image to CD or DVD. To

ensure the best results when recovering your system using a CD or Acer eRecovery Management,

detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer

ezDock.

Chapter 1

Acer eSettings Management

Acer eSettings Management allows you to inspect hardware specifications, set BIOS passwords and modify

boot options.

Acer eSettings Management also:

Provides a simple graphical user interface for navigation.

Prints and saves hardware specifications.

Lets you set an asset tag for your system.

Chapter 1

Windows Mobility Center

The Windows Mobility Center collects key mobile-related system settings in one easy-to-find place, so you can

quickly configure your Acer system to fit the situation as you change locations, networks or activities. Settings

include display brightness, volume, power plan, wireless networking on/off, external display settings,

synchronization status and presentation settings.

Windows Mobility Center also includes Acer-specific settings like sharing folders overview/sharing service on

or off, Bluetooth Add Device (if applicable), and a shortcut to the Acer user guide, drivers and utilities.

To launch Windows Mobility Center:

Use the shortcut key <

> + <X>.

Start Windows Mobility Center from the Control panel.

Start Windows Mobility Center from the Accessories program group in the Start menu.

Launch Windows Mobility Center by right-clicking

in the system tray and select Windows Mobility

Center.

Chapter 1

Using the System Utilities

Acer Bio-Protection (only for certain models)

Acer Bio-Protection Fingerprint Solution is a multi-purpose fingerprint software package integrated with the

Microsoft Windows operating system. Utilizing the uniqueness of one's fingerprint features, Acer Bio-

Protection Fingerprint Solution has incorporated protection against unauthorized access to your computer with

centralized password management with Password Bank, easy music player launching with Acer MusicLaunch,

secure Internet favorites via Acer MyLaunch, and fast application/website launching and login with Acer

FingerLaunch, while Acer ProfileLaunch can launch up to three applications/websites from a single finger

swipe.

Acer Bio-Protection Fingerprint Solution also allows you to navigate through web browsers and documents

using Acer FingerNav. With Acer Bio-Protection Fingerprint Solution, you can now enjoy an extra layer of

protection for your personal computer, as well as the convenience of accessing your daily tasks with a simple

swipe of your finger!

For more information refer to the Acer Bio-Protection help files.

Chapter 1

Acer GridVista (dual-display compatible)

NOTE: This feature is only available on certain models.

To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then

select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the

display box and then click the check box Extend my windows desktop onto this monitor. Finally, click

Apply to confirm the new settings and click OK to complete the process.

Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows

on the same screen. To access this function, please go to Start>All Programs and click on Acer GridVista.

You may choose any one of the four display settings indicated below:

Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display

compatible, allowing two displays to be partitioned independently.

Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.

AcerGridVista is simple to set up:

Run Acer GridVista and select your preferred screen configuration for each display from the task bar.

Drag and drop each window into the appropriate grid.

Enjoy the convenience of a well-organized desktop.

Chapter 1

NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's

recommended value.

Chapter 1

Hardware Specifications and Configurations

Processor

Item

Specification

CPU type

Intel® Core™2 Duo Mobile Processor P8400 (2.26G), P8600 (2.4

G), P9500 (2.53G), T9400 (2.53G), T9600 (2.8G)

Core logic

Mobile Intel® 945 Express Chipset

CPU package

Socket B (P8400, P8600, P9500) and Socket P (T9400, T9600)

CPU core voltage

1.0375V to 1.3V

CPU Fan True Value Table

DTS(degree C)

Fan Speed (rpm)

Acoustic Level (dBA)

45-50

0-3000

55-66

0-3300

68-74

3300-3800

78-83

3800-4100

86-91

4100-4800

Throttling 50%: On= 99°

C; OFF=93°

OS shut down at 105°

C; H/W shot down at 110°

BIOS

Item

Specification

BIOS vendor

Phoenix

BIOS Version

1.04c

System Memory

Item

Specification

Memory controller

Built-in

Memory size

0MB (no on-board memory)

DIMM socket number

2 sockets

Supports memory size per socket

2048MB

Supports maximum memory size

4G for 64bit OS (with two 2GB SODIMM)

Supports DIMM type

DDR 2 Synchronous DRAM

Supports DIMM Speed

667 MHz

Supports DIMM voltage

1.8V and 0.9V

Supports DIMM package

200-pin soDIMM

Memory module combinations

You can install memory modules in any combinations as long as

they match the above specifications.

Chapter 1

Memory Combinations

Slot 1

Slot 2

Total Memory

0MB

256MB

0MB

512MB

0MB

1024MB

0MB

2048MB

256MB

512MB

256MB

512MB

768MB

256MB

1024MB

1280MB

256MB

2048MB

2304MB

512MB

256MB

768MB

512MB

1024MB

512MB

1024MB

1536MB

512MB

2048MB

2560MB

1024MB

0MB

1024MB

256MB

1280MB

1024MB

512MB

1536MB

1024MB

2048MB

1024MB

2048MB

3072MB

2048MB

0MB

2048MB

256MB

2304MB

2048MB

512MB

2560MB

2048MB

1024MB

3072MB

2048MB

4096MB

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various

capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be

reversed.

Item

Specification

LAN Chipset

Broadcom BCM5764/Broadcom BCM5765

Supports LAN protocol

10/100/1000 Mbps

LAN connector type

RJ45

LAN connector location

Left side

Features

Integrated 10/100 BASE-T transceiver

Wake on LAN support compliant with ACPI 2.0

PCI v2.2

Bluetooth Interface

Item

Specification

Chipset

Foxconn Bluetooth FOX_BRM_2.0 F/W 300

Data throughput

723 bps (full speed data rate)

Protocol

Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG

specification is ratified).

Interface

USB 1.1

Chapter 1

Bluetooth Interface

Item

Specification

Connector type

USB

Wireless Module 802.11b/g

Item

Specification

Chipset

WLAN 802.11ABGN SHIRLEYPEAK1*2

Data throughput

11~54 Mbps, up to 270 Mbps for Draft-N

Protocol

802.11b+g, Draft-N

Interface

PCI bus (mini PCI socket for wireless module)

Hard Disk Drive Interface

Item

Vendor &

HGST

WD1600BEVT-

SEAGATE SATA

WD WD3200BEVT-

Model Name

HTS542512K9SA00

22ZCT0

ST9250827AS

22ZCT0 ML125

BRONCO-B LF

HITACHI

TOSHIBA

SEAGATE

HTS541616J9SA00

MK2546GSX LF

ST9120817AS LF

HGST

TOSHIBA

SEAGATE SATA

HTS542525K9SA00

MK1246GSX LF

ST9160827AS

WD1200BEVS-

TOSHIBA

WD WD2500BEVS-

22UST0 ML125 LF

MK1646GSX LF

22UST0 ML125

Capacity

120000

160000

250000

320000

(MB)

Bytes per

512

N/A

sector

Data heads

3/4

N/A

Drive Format

Disks

N/A

Spindle

5400 RPM

speed

(RPM)

Performance Specifications

Buffer size

8MB

Interface

SATA

Max. media

540

850

transfer rate

(disk-buffer,

Mbytes/s)

DC Power Requirements

Voltage

5V(DC) +/- 5%

tolerance

Chapter 1

Optical Disc Drive

Item

Specification

Vendor & model name

TOSHIBA SUPER-MULTI DRIVE DL 8X TS-L633A LF

PIONEER SUPER-MULTI DRIVE 8X DVR-TD08RS LF

PANASONIC SUPER-MULTI DRIVE DL 8X UJ-870A LF

HLDS SUPER-MULTI DRIVE TRAY DL 8X GSA-T50N LF

HLDS SUPER-MULTI DRIVE DL 8X GSA-T50N LF

SONY SUPER-MULTI DRIVE DL 8X AD-7560S LF

PLDS SUPER-MULTI DRIVE DL 8X DS-8A2S LF

Performance Specification

With CD Diskette

With DVD Diskette

Transfer rate (KB/sec)

Sustained:

Max 3.6Mbytes/sec

Max 10.08Mbytes/sec

Buffer Memory

2MB

Interface

SATA

Applicable disc format

CD: CD-DA, CD-ROM, CD-ROM XA, Photo CD (multi-session), Video

CD, Cd-Extra (CD+), CD-text

DVD: DVD-VIDEO, DVD-ROM, DVD-R (3.9GB, 4.7GB) DVD-R DL,

DVD-RW, DVD-RAM, DVD+R, DVD+R DL, DVD+RW

CD:

CD-DA (Red Book) - Standard Audio CD & CD-TEXT

CD-ROM (Yellow Book Mode1 & 2) - Standard Data

CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session

CD-I (Green Book, Mode2 Form1 & 2, Ready, Bridge)

CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video

Video-CD (White Book) - MPEG1 Video

CD-R (Orange Book Part)

CD-RW & HSRW (Orange Book Part Volume1 & Volume 2

Super Audio CD (SACD) Hybrid type

US & US+ RW

DVD:

DVD-ROM (Book 1.02), DVD-Dual

DVD-Video (Book 1.1)

DVD-R (Book 1.0, 3.9G)

DVD-R (Book 2.0, 4.7G) - General & Authoring

DVD+R (Version 1.0)

DVD+RW

DVD-RW (Non CPRM & CPRM)

DVD°”R Dual

Loading mechanism

Load: Manual

Release: (a) Electrical Release (Release Button)

(b) Release by ATAPI command

Power Requirement

Input Voltage

5 V +/- 5% (Operating)

Chapter 1

Audio Interface

Item

Specification

Audio Controller

Realtek ALC883 Azalia and Amplifier Maxim MAX9710 &

MAX4411

Audio onboard or optional

Built-in

Mono or Stereo

Stereo

Resolution

18 bit stereo full duplex

Compatibility

HD audio Interface; S/PDIF output for PCM or AC-3

content

Sampling rate

1Hz resolution VSR (Variable Sampling Rate)

Internal microphone

Yes

Internal speaker / Quantity

Yes/2 (1.5W speakers)

Video Memory

Item

Specification

Chipset

VGA CARD NB9P-GS/Intel GMA970 VGA

Memory size

512M GDDR3/

Item

Specification

Chipset

ICH8M

USB Compliancy Level

2.0

OHCI

USB 1.1 and USB 2.0 Host controller

Number of USB port

Location

Two on the right side/one on the front

Serial port function control

Enable/Disable by BIOS Setup

System Board Major Chips

Item

Controller

Core logic

Mobile Intel® GM945/PM945 + ICH8M Express Chipset

VGA

nVidia GeForce 9300 GS/9600M GT/UMA

USB 2.0

Intel ICH8M

Super I/O controller

N/A

MODEM

ALC 883

Bluetooth

FOXCONN BCM2045 V2

Wireless 802.11 b+g

WLAN 802.11ABGN SHIRLEYPEAK1*2

PCMCIA/ 5 in 1 Card Reader

JMicron Cardreader JMB385

Audio Codec

Audio Azalia(ALC888S)

Keyboard

Item

Specification

Keyboard controller

NS PC97541V

Chapter 1

Keyboard

Item

Specification

Total number of keypads

84-/85-key

Windows logo key

Yes

Internal & external keyboard work

Plug USB keyboard to the USB port directly: Yes

simultaneously

Battery

Item

Specification

Vendor

Panasonic/Sanyo/Sony/Simplo

Battery Type

Li-ion

Pack capacity

6Cell 4400 MAH/8Cell 4800 MAH

Number of battery cell

6/8

Package configuration

3 cells in series, 2 series in parallel

4 cells in series, 2 series in parallel

LCD 15.4” inch

Item

Specification

Vendor & model name

CMO/AUO/LG

Screen Diagonal (mm)

15.4 inches

Display resolution (pixels)

1280 x 800 WXGA

Pixel Pitch

0.204 x 0.204

Pixel Arrangement

R.G.B. Vertical Stripe

Display Mode

Normally White

Typical White Luminance (NIT)

220

also called Brightness

Luminance Uniformity

1.25 max.

Contrast Ratio

400 typical

Response Time msec

Nominal Input Voltage VDD

+3.3V

Viewing Angle (degree)

Horizontal: Right/Left

45/45

Vertical: Upper/Lower

15/35

Temperature Range(°C)

0 to +50

Operating

-40 to +60

Storage (shipping)

AC Adaptor

Item

Specification

Input

100-240V~ 1.5A, 50-60Hz/

Output

19V 4.74A 90W/19V 3.42A 65W

Chapter 1

System Power Management

ACPI mode

Power Management

Mech. Off (G3)

All devices in the system are turned off completely.

Soft Off (G2/S5)

OS initiated shutdown. All devices in the system are turned

off completely.

Working (G0/S0)

Individual devices such as the CPU and hard disc may be

power managed in this state.

Suspend to RAM (S3)

CPU set power down

VGA Suspend

PCMCIA Suspend

Audio Power Down

Hard Disk Power Down

CD-ROM Power Down

Super I/O Low Power mode

Save to Disk (S4)

Also called Hibernation Mode. System saves all system

states and data onto the disc prior to power off the whole

system.

Chapter 1

Chapter 1

Chapter 2

System Utilities

BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/

Output System).

Your computer is already properly configured and optimized, and you do not need to run this utility. However, if

you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4

Troubleshooting when problem arises.

To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted

on the bottom of screen).

Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change

boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.

Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without

entering BIOS SETUP Utility.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

CPU Type:

Intel

(R) Core

(TM)2 Duo CPU T9400 @ 2.53 GHz

CPU Speed:

2.53

GHz

IDE0 Model Name:

XXXXXXXXXXX-(XX)

IDE0 Serial Number:

XXXXXXXX

ATAPI Model Name:

XXXXXXXXXXX-XXX XX-XXXX-(XX)

System BIOS Version:

VX.XX

VGA BIOS Version:

XX-XXX XXXXXX.XXX.XXX.XXX.XXXXXX

KBC Version:

XX.XX

Serial Number:

XXXXXXXXXXXXXXXXXXXXXXX

Asset Tag Number:

None

Product Name:

Aspire

5930

Manufacturer Name:

Acer

UUID:

XXXxXxXX-xXxX-XXxx-xXXx-xXXxXXxXxxXX

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

Chapter 2

Navigating the BIOS Utility

There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.

Follow these instructions:

To choose a menu, use the left and right arrow keys.

To choose an item, use the up and down arrow keys.

To change the value of a parameter, press F5 or F6.

A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.

Press Esc while you are in any of the menu options to go to the Exit menu.

In any menu, you can load default settings by pressing F9. You can also press F10 to save any

changes made and exit the BIOS Setup Utility.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a

particular menu are shown on the bottom of the screen. Help for parameters are found in the Item

Specific Help part of the screen. Read this carefully when making changes to parameter values. Please

note that system information is subject to different models.

Chapter 2

Information

The Information screen displays a summary of your computer hardware information.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

CPU Type:

Intel

(R) Core

(TM)2 Duo CPU T9400 @ 2.53 GHz

CPU Speed:

2.53

GHz

IDE0 Model Name:

XXXXXXXXXXX-(XX)

IDE0 Serial Number:

XXXXXXXX

ATAPI Model Name:

XXXXXXXXXXX-XXX XX-XXXX-(XX)

System BIOS Version:

VX.XX

VGA BIOS Version:

XX-XXX XXXXXX.XXX.XXX.XXX.XXXXXX

KBC Version:

XX.XX

Serial Number:

XXXXXXXXXXXXXXXXXXXXXXX

Asset Tag Number:

None

Product Name:

Aspire

5930

Manufacturer Name:

Acer

UUID:

XXXxXxXX-xXxX-XXxx-xXXx-xXXxXXxXxxXX

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

NOTE: The system information is subject to different models.

Parameter

Description

CPU Type

This field shows the CPU type and speed of the system.

CPU Speed

This field shows the speed of the CPU.

IDE0 Model Name

This field shows the model name of HDD installed on primary IDE master.

IDE0 Serial Number

This field displays the serial number of HDD installed on primary IDE master.

ATAPI Model Name

This field shows the model name of the Optical device installed in the system.

System BIOS Version

Displays system BIOS version.

VGA BIOS Version

This field displays the VGA firmware version of the system.

KBC Ver

This field shows the keyboard

Serial Number

This field displays the serial number of this unit.

Asset Tag Number

This field displays the asset tag number of the system.

Product Name

This field shows product name of the system.

Manufacturer Name

This field displays the manufacturer of this system.

UUID Number

Universally Unique Identifier (UUID) is an identifier standard used in software construction,

standardized by the Open Software Foundation (OSF) as part of the Distributed

Computing Environment (DCE).

Chapter 2

Main

The Main screen allows the user to set the system time and date as well as enable and disable boot option

and recovery.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

Item Specific Help

System Time:

[10:10:10]

System Date:

[04/28/2008]

<Tab>,

<Shift-Tab>, or

System Memory:

640 KB

<Enter> selects field.

Extended Memory:

4093 MB

Video Memory:

512 MB

Quiet Boot:

[Enabled]

Network Boot:

[Enabled]

F12 Boot Menu:

[Disabled]

D2D Recovery:

[Enabled]

SATAMode

[AHCI]

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

NOTE: The screen above is for your reference only. Actual values may differ.

Chapter 2

The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter

Description

Format/Option

System Time

Sets the system time. The hours are displayed

Format: HH:MM:SS

with 24-hour format.

(hour:minute:second) System Time

System Date

Sets the system date.

Format MM/DD/YYYY (month/day/

year)

System Date

System Memory

This field reports the memory size of the system.

Memory size is fixed to 640MB

Extended Memory

This field reports the memory size of the

extended memory in the system.

Extended Memory size=Total memory size-1MB

VGA Memory

Shows the VGA memory size.

Quiet Boot

Determines if Customer Logo will be displayed or

Option: Enabled or Disabled

not; shows Summary Screen is disabled or

enabled.

Enabled: Customer Logo is displayed, and

Summary Screen is disabled.

Disabled: Customer Logo is not displayed, and

Summary Screen is enabled.

Network Boot

Enables, disables the system boot from LAN

Option: Enabled or Disabled

(remote server).

F12 Boot Menu

Enables, disables Boot Menu during POST.

Option: Disabled or Enabled

D2D Recovery

Enables, disables D2D Recovery function. The

Option: Enabled or Disabled

function allows the user to create a hidden

partition on hard disc drive to store operation

system and restore the system to factory

defaults.

SATA Mode

Control the mode in which the SATA controller

Option: AHCI or IDE

should operate.

NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is

because the user is not allowed to control the settings in these cases.

Chapter 2

Security

The Security screen contains parameters that help safeguard and protect your computer from unauthorized

use.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

Item Specific Help

Supervisor Password is:

Clear

User Password is:

Clear

HDD Password is:

Clear

Supervisor Password

controls access of the

Set Supervisor Password

[Enter]

whole setup utility.

Set User Password

[Enter]

It can be used to boot

Set

HDD

Password

[Enter]

up when Password on

boot is enabled.

Password on Boot:

[Disabled]

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

NOTE: Please refer to “Remove HDD/BIOS Password” section if you need to know how to remove HDD/BIOS

Password.

Chapter 2

The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter

Description

Option

Supervisor Password Is

Shows the setting of the Supervisor password

Clear or Set

User Password Is

Shows the setting of the user password.

Clear or Set

HDD Password Is

Shows the setting of the hard disk password.

Clear or Set

Set Supervisor Password

Press Enter to set the supervisor password.

When set, this password protects the BIOS

Setup Utility from unauthorized access. The

user can not either enter the Setup menu nor

change the value of parameters.

Set User Password

Press Enter to set the user password. When

user password is set, this password protects

the BIOS Setup Utility from unauthorized

access. The user can enter Setup menu only

and does not have right to change the value of

parameters.

Set HDD Password

Enter HDD Password.

Password on Boot

Defines whether a password is required or not

Disabled or Enabled

while the events defined in this group

happened. The following sub-options are all

requires the Supervisor password for changes

and should be grayed out if the user password

was used to enter setup.

NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget

your password. If you forget your password, you may have to return your notebook computer to your

dealer to reset it.

Setting a Password

Follow these steps as you set the user or the supervisor password:

Use the “w” and “y” keys to highlight the Set Supervisor Password parameter and press the e key. The

Set Supervisor Password box appears:

Type a password in the “Enter New Password” field. The password length can not exceeds 8

alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New

Password” field.

IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.

Press e.

After setting the password, the computer sets the User Password parameter to “Set”.

If desired, you can opt to enable the Password on boot parameter.

When you are done, press u to save the changes and exit the BIOS Setup Utility.

Chapter 2

Removing a Password

Follow these steps:

Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set

Password box appears:

Type the current password in the Enter Current Password field and press e.

Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The

computer then sets the Supervisor Password parameter to “Clear”.

When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.

Changing a Password

Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set

Password box appears:

Type the current password in the Enter Current Password field and press e.

Type a password in the Enter New Password field. Retype the password in the Confirm New Password

field.

Press e. After setting the password, the computer sets the User Password parameter to “Set”.

If desired, you can enable the Password on boot parameter.

When you are done, press u to save the changes and exit the BIOS Setup Utility.

If the verification is OK, the screen will display as following.

The password setting is complete after the user presses u.

Chapter 2

If the current password entered does not match the actual current password, the screen will show you the

Setup Warning.

If the new password and confirm new password strings do not match, the screen will display the following

message.

Chapter 2

Intel

The Intel screen allows the user to set the Legacy OS Boot, CPU, MCH, ICH and ACPI Control Sub-Menu and

the Video Repost.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

Item Specific Help

Legacy OS Boot:

[Enabled]

CPU Control Sub Menu

MCH Control Sub-Menu

Select Enabled to

ICH Control Sub-Menu

attempt Legacy OS

ACPI Control Sub-Menu

Boot only.

Video Repost:

[Linux]

Select Disabled to

attempt EFI Boot first,

Legacy OS Boot Second.

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested

parameter settings.

Parameter

Description

Format/Option

Legacy OS Boot

Let you choose which to boot first, EFI or Legacy

Option: Enabled or Disabled

OS.

CPU Control Sub-Menu

These items control various CPU parameters

MCH Control Sub-Menu

These items control various MCH parameters

ICH Control Sub-Menu

These items control various ICH parameters

ACPI Control Sub-Menu

These items control various ACPI parameters

Video Repost

Select if a Video Repost is to be performed

Option: Linux, Enabled or Disabled

during resume from S3

Chapter 2

Boot

This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices

includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

Item Specific Help

Boot priority order:

1: IDE HDD: XXXXXXXXXXX-(XX)

Use < > or < > to

IDE CD: XXXXXXXXXXX-XXX XX-XXXX-XX

select a device, then

PCI LAN: Network Boot

press

<F6> to move it

USB HDD:

up the list, or

<F5>

USB FDD:

to move it down the

USB Key:

list. Press

<Esc> to

USB CDROM:

escape the menu.

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

Chapter 2

Exit

The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the

BIOS Setup Utility.

Phoenix SecureCore(tm) Setup Utility

Information

Main

Security

Intel

Boot

Exit

Item Specific Help

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

Exit System Setup and

Discard Changes

save your changes to

Save Changes

CMOS.

Help

Select Item

-/+

Change Values

Setup Defaults

Esc

Exit

Select Menu

Enter

Select

Sub-Menu

F10

Save and Exit

The table below describes the parameters in this screen.

Parameter

Description

Exit Saving Changes

Exit System Setup and save your changes to CMOS.

Exit Discarding Changes

Exit utility without saving setup data to CMOS.

Load Setup Default

Load default values for all SETUP item.

Discard Changes

Load previous values from CMOS for all SETUP items.

Save Changes

Save Setup Data to CMOS.

Chapter 2

BIOS Flash Utility

The BIOS flash memory update is required for the following conditions:

New versions of system programs

New features or options

Restore a BIOS when it becomes corrupted.

Use the Flash utility to update the system BIOS flash ROM.

NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery

Diskette before you use the Flash utility.

NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.

NOTE: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does not

contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not

completely loaded.

Fellow the steps below to run the Flash.

Prepare a bootable diskette.

Copy the flash utilities to the bootable diskette.

Then boot the system from the bootable diskette. The flash utility has auto-execution function.

Chapter 2

Remove HDD/BIOS Utility

This section provide you with removing HDD/BIOS method:

Remove HDD Password:

If you key in wrong HDD password for three time, “HDD password error code” would display on the

screen. See the image below.

If you need to solve HDD password locked problem, you can run HDD_PW.EXE

1. Key in “hdd_pw 15494 0”

2. Select “2”

3. Choose one upper-case string

Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password.

Chapter 2

Remove BIOS Password:

If you key in wrong Supervisor Password for three time, “System Disabled” would display on the

screen. See the image below.

Chapter 2

If you need to solve BIOS password locked problem, you can run BIOS_PW.EXE

1. Key in “bios_pw 14452 0”

2. Choose one upper-case string

Reboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password.

Chapter 2

Chapter 2

Chapter 2

Chapter 3

Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for

maintenance and troubleshooting.

Disassembly Requirements

To disassemble the computer, you need the following tools:

Wrist grounding strap and conductive mat for preventing electrostatic discharge

Flat screwdriver

Philips screwdriver

Hex screwdriver

Plastic flat screwdriver

Plastic tweezers

NOTE: The screws for the different components vary in size. During the disassembly process, group the

screws with the corresponding components to avoid mismatch when putting back the components.

Chapter 3

General Information

Pre-disassembly Instructions

Before proceeding with the disassembly procedure, make sure that you do the following:

Turn off the power to the system and all peripherals.

Unplug the AC adapter and all power and signal cables from the system.

Place the system on a flat, stable surface.

Remove the battery pack.

Disassembly Process

The disassembly process is divided into the following stages:

•

External module disassembly

•

Main unit disassembly

•

LCD module disassembly

The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.

Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you

want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly

frame in that order.

Main Screw List

Item

Screw

Color

Part No.

M2 x L4

Black

86.00E13.524

M2.5 x L6

Black

86.00E12.536

M2 x L3

Black

86.9A522.3R0

M3 x L4

Silver

86.9A524.4R0

M2.5 x L10

Black

86.00F84.73A

Chapter 3

External Module Disassembly Process

External Modules Disassembly Flowchart

The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you

on the components that need to be removed during servicing. For example, if you want to remove the main

board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.

EXTERNAL MODULE DISASSEMBLY

TURN OFF POWER

AND PERIPHERALS

UNPLUG POWER

CABLES

REMOVE BATTERY

PACK

ExpressCard

SD DUMMY CARD

DUMMY CARD

Captive Screwx6

Bx1

LOWER

COVER

Ax2

Ax1

Bx1

Ax1

WLAN

TV TUNER

DIMM

ODD

HDD

BOARD

MODULE

MODULES

MODULE

Ax2

Cx2

Dx2

MODEM

CARD

OPTICAL DISK

OPTICAL

HARD DISK

DRIVE

LOCKER

BRACKET

DRIVE

BRACKET

Screw List

Item

Screw

Color

Part No.

M2 x L4

Black

86.00E13.524

M2.5 x L6

Black

86.00E12.536

M2 x L3

Black

86.9A522.3R0

M3 x L4

Silver

86.9A524.4R0

Chapter 3

Removing the Battery Pack

Turn base unit over.

Slide the battery lock/unlock latch to the unlock position.

Slide the battery release latch to the release position to pop out the battery pack, then remove the battery

pack from the main unit.

Chapter 3

Removing the SD dummy card

Push the SD dummy card all the way in to eject it.

Pull it out from the slot.

Removing the ExpressCard dummy card

Push the ExpressCard dummy card all the way in to eject it.

Chapter 3

Pull it out from the slot.

Removing the Lower Cover

See “Removing the Battery Pack” on page 60.

Remove the six captive screws and the one screw (B) on the lower cover.

Step

Size (Quantity)

Color

Torque

M2.5 x L6 (1)

Black

1.6 kgf-cm

Use a plastic screw driver to carefully pry open the lower cover.

Chapter 3

Remove the lower cover from the lower case.

Removing the DIMM

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62..

Push out the latches on both sides of the DIMM socket to release the DIMM.

Remove the DIMM module.

Removing the WLAN Board Modules

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

Chapter 3

Disconnect the antenna cables from the WLAN board.

NOTE: There are 3 antenna cables connected to the WLAN board module. The Black antenna cable is

connected to number 1 connector, the White antenna cable is connected to number 2 connector and

the Gray antenna cable is connected to number 3 connector.

Move the antenna away from the WLAN board and remove the one screw (A) on the WLAN board to

release the WLAN board.

Step

Size (Quantity)

Color

Torque

M2 x L4 (1)

Black

1.6 kgf-cm

Detach the WLAN board from the WLAN socket.

NOTE: When attaching the antenna back to the WLAN board, make sure the cable are arranged properly.

Removing the TV Tuner Board Modules

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

Chapter 3

Disconnect the antenna cable from the TV tuner board and remove the one screw (A) to release the

board.

Step

Size (Quantity)

Color

Torque

M2 x L4 (1)

Black

1.6 kgf-cm

Detach the TV tuner board from the socket.

NOTE: When attaching the antenna back to the TV tuner board, make sure the cable are arranged properly.

Removing the Modem Board

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the TV Tuner Board Modules” on page 64..

Remove the two screws (A) securing the modem card.

Step

Size (Quantity)

Color

Torque

1~2

M2 x L4 (2)

Black

1.6 kgf-cm

Chapter 3

Lift the modem board from the system.

Disconnect the cable from the modem board.

Removing the Hard Disk Drive Module

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

Remove the one screw (A) securing the hard disk drive module.

Step

Size (Quantity)

Color

Torque

M2 x L4 (1)

Black

3.0 kgf-cm

Chapter 3

Slide the hard disk drive module away from the connector.

Use the plastic tab to lift the hard disk drive module and remove it from the hard disk drive bay.

NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.

Remove the two screws (D) securing the hard disk to the bracket and remove the hard disk from the

bracket.

Chapter 3

Step

Size (Quantity)

Color

Torque

1~2

M3 x L4 (2)

Silver

3.0 kgf-cm

Removing the Optical Drive Module

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

Release the antenna cables from the latches as shown.

Remove the one screw (B) from the bottom panel.

Step

Size (Quantity)

Color

Torque

M2.5 x L6 (1)

Black

3.0 kgf-cm

Chapter 3

Use a pin and push it inside the emergency eject hole to eject the odd drive tray.

Carefully pull out the odd drive tray until the part of the module is visible and then slowly push back to

close the tray into the module with the module still partially exposed.

Slowly pull out the odd module from the odd drive bay.

Chapter 3

10. Remove the two screws (C) securing the locker bracket and remove the locker bracket from the optical

disk drive module.

Step

Size (Quantity)

Color

Torque

1~2

M2 x L3 (2)

Silver

1.6 kgf-cm

Chapter 3

Main Unit Disassembly Process

Main Unit Disassembly Flowchart

MAIN UNIT DISASSEMBLY

MAIN UNIT

Ax2

KEYBOARD

MIDDLE COVER

HEAT SINK FAN

SCREW X 5 (CPU)

SCREW X 4 (VGA)

POWER

CPU/VGA

BOARD

THERMAL MODULE

Bx2, Ex2

Ax2

LCD MODULE

CPU

VGA CARD

Bx13,Ax3

UPPER CASE

Ax3

Ax4

Ax2

Ax4

Ax1

MEDIA

E-KEY

SPEAKER

LAUNCH

TOUCHPAD

BOARD

MODULE

MAIN

BOARD

BRACKET

BOARD

Ax1

AUDIO

USB

SUBWOOFER

BLUETOOTH

TOUCHPAD

BOARD

FINGERPRINT

MODULE

Screw List

Item

Screw

Color

Part No.

M2 x L4

Black

86.00E13.524

M2.5 x L6

Black

86.00E12.536

M2.5 x L10

Black

86.00F84.73A

Chapter 3

Removing the Keyboard

See “Removing the Battery Pack” on page 60.

Push down on the lock and release the latches securing the keyboard to the upper case.

Carefully pry loose the keyboard and turn it over on the touchpad area.

Chapter 3

Disconnect the keyboard cable from the main board to remove the keyboard.

Removing the Middle Cover

See “Removing the Battery Pack” on page 60.

Use a plastic screw driver to pry loose the side of the middle cover.

Chapter 3

Carefully pry loose the middle cover from the latches securing it and remove the middle cover.

Removing the Power Board

See “Removing the Battery Pack” on page 60.

See “Removing the Middle Cover” on page 73..

Disconnect the cable from the Power Board connector.

Chapter 3

Remove the one screw (A) securing the Power Board to the upper case.

Step

Size (Quantity)

Color

Torque

M2 x L4 (1)

Black

1.6 kgf-cm

Release the Power Board from the latches and remove the Power Board from the upper case.

Removing the Heatsink Fan Module

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

Remove the two screws (A) securing the heatsink fan module in place.

Step

Size (Quantity)

Color

Torque

1~2

M2 x L4 (2)

Black

1.6 kgf-cm

Chapter 3

Lift the heatsink fan module and disconnect the heatsink fan connector from the main board.

Carefully lift up the heatsink fan module.

Removing the CPU and VGA Heatsink Module

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the Heatsink Fan Module” on page 75.

Remove the four screws securing the VGA board heatsink module (Discrete Model only) and the five

screw securing the CPU heatsink module.

Chapter 3

Carefully remove the heatsink module from the system.

Removing the CPU

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the Heatsink Fan Module” on page 75.

See “Removing the CPU and VGA Heatsink Module” on page 76.

Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU.

Chapter 3

Lift up carefully to remove the CPU.

NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown.

Removing the VGA Board (Discrete Model only)

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the Heatsink Fan Module” on page 75.

See “Removing the CPU and VGA Heatsink Module” on page 76.

Remove the two screws (A) securing the VGA board to the main board.

Step

Size (Quantity)

Color

Torque

1~2

M2 x L4 (2)

Black

1.6 kgf-cm

Chapter 3

Remove the VGA board from the main board.

Removing the LCD Module

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. Turn over the system and remove the two screws (B) from the bottom of the left and right hinges.

Step

Size (Quantity)

Color

Torque

1~2

M2.5 x L6 (2)

Black

3.0 kgf-cm

Chapter 3

12. Carefully pull out the wireless antenna cables from the hole and release the cables from the latches.

13. Disconnect the LCD cable connector from the main board.

14. Remove the two screws (E) from the left and right hinge of the LCD module.

Step

Size (Quantity)

Color

Torque

1~2

M2.5 x L10 (2)

Black

4.0 kgf-cm

Chapter 3

15. Carefully remove the LCD module from the base unit.

NOTE: When connecting the cable back to the unit, please note that the cable should be routed well.

Separating the Upper Case from the Lower Case

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Optical Drive Module” on page 68.

10. See “Removing the Keyboard” on page 72.

11. See “Removing the Middle Cover” on page 73.

12. See “Removing the Power Board” on page 74.

13. See “Removing the Heatsink Fan Module” on page 75.

14. See “Removing the CPU and VGA Heatsink Module” on page 76.

15. See “Removing the CPU” on page 77.

16. See “Removing the VGA Board (Discrete Model only)” on page 78.

17. See “Removing the LCD Module” on page 79.

18. Disconnect the touchpad cable from the TPAD1 connector on the main board.

Chapter 3

19. Disconnect the fingerprint cable from the FP1 connector on the main board.

20. Disconnect the launch board cable from the LAUNCH1 connector on the main board.

Chapter 3

21. Disconnect the power cable from the PWRCN1 connector on the main board.

22. Disconnect the media board cable from the MEDIA1 connector on the main board.

Chapter 3

23. Disconnect the E-key connector from the main board.

24. Disconnect the speaker cable from the INTSPK1 connector on the main board.

Chapter 3

25. Remove the eleven screws (11 x B) from the bottom panel.

Step

Size (Quantity)

Color

Torque

1~11

M2.5 x L6 (11)

Black

3.0 kgf-cm

26. Turn the unit over and remove the 5 screws (2 x B, 3 x A) from the top panel.

Step

Size (Quantity)

Color

Torque

1~2

M2.5 x L6 (2)

Black

3.0 kgf-cm

3~5

M2 x L4 (3)

Black

1.6 kgf-cm

27. Gently remove the upper case from the lower case.

Removing the Media Board

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

Chapter 3

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Optical Drive Module” on page 68.

10. See “Removing the Keyboard” on page 72.

11. See “Removing the Middle Cover” on page 73.

12. See “Removing the Power Board” on page 74.

13. See “Removing the Heatsink Fan Module” on page 75.

14. See “Removing the CPU and VGA Heatsink Module” on page 76.

15. See “Removing the CPU” on page 77.

16. See “Removing the VGA Board (Discrete Model only)” on page 78.

17. See “Removing the LCD Module” on page 79.

18. See “Separating the Upper Case from the Lower Case” on page 81.

19. Release the media board from the latches.

20. Turn over the media board to gain access to the cable.

Chapter 3

21. Disconnect the cable from the media board to remove the board from the upper case.

Removing the E-key Board

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. See “Removing the Power Board” on page 74.

12. See “Removing the Heatsink Fan Module” on page 75.

13. See “Removing the CPU and VGA Heatsink Module” on page 76.

14. See “Removing the CPU” on page 77.

15. See “Removing the VGA Board (Discrete Model only)” on page 78.

16. See “Removing the LCD Module” on page 79.

17. See “Separating the Upper Case from the Lower Case” on page 81.

Chapter 3

18. Disconnect the cable from the E-key board.

19. Remove the three screws (3 x A) securing the E-key board.

Step

Size (Quantity)

Color

Torque

1~3

M2 x L4 (3)

Black

1.6 kgf-cm

20. Remove the E-key board from the upper case.

Chapter 3

Removing the Speaker Module

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. See “Removing the Power Board” on page 74.

12. See “Removing the Heatsink Fan Module” on page 75.

13. See “Removing the CPU and VGA Heatsink Module” on page 76.

14. See “Removing the CPU” on page 77.

15. See “Removing the VGA Board (Discrete Model only)” on page 78.

16. See “Removing the LCD Module” on page 79.

17. See “Separating the Upper Case from the Lower Case” on page 81.

18. Remove the four screws (4 x A) securing the speaker module.

Step

Size (Quantity)

Color

Torque

1~4

M2 x L4 (4)

Black

1.6 kgf-cm

19. Remove the cable that is glued to the speaker module.

Chapter 3

20. Remove the speaker module from the upper case.

Removing the Launch Board

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. See “Removing the Power Board” on page 74.

12. See “Removing the Heatsink Fan Module” on page 75.

13. See “Removing the CPU and VGA Heatsink Module” on page 76.

14. See “Removing the CPU” on page 77.

15. See “Removing the VGA Board (Discrete Model only)” on page 78.

16. See “Removing the LCD Module” on page 79.

17. See “Separating the Upper Case from the Lower Case” on page 81.

18. Disconnect the cable from the launch board.

Chapter 3

19. Remove the two screws (2 x A) securing the launch board module.

Step

Size (Quantity)

Color

Torque

1~2

M2 x L4 (2)

Black

1.6 kgf-cm

20. Remove the launch board module from the upper case.

Removing the Fingerprint and Touchpad Module

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

Chapter 3

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. See “Removing the Power Board” on page 74.

12. See “Removing the Heatsink Fan Module” on page 75.

13. See “Removing the CPU and VGA Heatsink Module” on page 76.

14. See “Removing the CPU” on page 77.

15. See “Removing the VGA Board (Discrete Model only)” on page 78.

16. See “Removing the LCD Module” on page 79.

17. See “Separating the Upper Case from the Lower Case” on page 81.

18. Remove the touchpad cable that is glued to the bracket.

19. Disconnect the touchpad cable from the touchpad board.

Chapter 3

20. Disconnect the fingerprint cable from the fingerprint board.

21. Remove the four screws (A) securing the bracket to the upper case.

Step

Size (Quantity)

Color

Torque

1~4

M2 x L4 (4)

Black

1.6 kgf-cm

22. Remove the touchpad bracket.

Chapter 3

23. Remove the fingerprint board module.

24. Carefully pry loose and remove the touch pad board.

WARNING:The touchpad board is glued to the upper case, only remove the touchpad board if it is defective.

Removing the Main Board

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Optical Drive Module” on page 68.

Chapter 3

10. See “Removing the Keyboard” on page 72.

11. See “Removing the Middle Cover” on page 73.

12. See “Removing the Power Board” on page 74.

13. See “Removing the Heatsink Fan Module” on page 75.

14. See “Removing the CPU and VGA Heatsink Module” on page 76.

15. See “Removing the CPU” on page 77.

16. See “Removing the VGA Board (Discrete Model only)” on page 78.

17. See “Removing the LCD Module” on page 79.

18. See “Separating the Upper Case from the Lower Case” on page 81.

19. Disconnect the USB cable from the USBCN1 connector on the main board.

20. Disconnect the subwoofer cable from the SPKR1 connector on the main board.

21. Disconnect the bluetooth cable from the BLUE1 connector on the main board.

Chapter 3

22. Disconnect the audio cable from the AUDIOCN1 connector on the main board.

23. Disconnect the DC cable from the DC1 connector on the main board.

24. Remove the one screw (A) securing the main board in place.

Step

Size (Quantity)

Color

Torque

M2 x L4 (1)

Black

1.6 kgf-cm

Chapter 3

25. Carefully remove the main board.

Removing the USB Board Module

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. See “Removing the Power Board” on page 74.

12. See “Removing the Heatsink Fan Module” on page 75.

13. See “Removing the CPU and VGA Heatsink Module” on page 76.

14. See “Removing the CPU” on page 77.

15. See “Removing the VGA Board (Discrete Model only)” on page 78.

16. See “Removing the LCD Module” on page 79.

17. See “Separating the Upper Case from the Lower Case” on page 81.

18. Disconnect the TV tuner antenna cable and the USB cable from the USB board module.

Chapter 3

19. Remove the one screw (A) securing the USB board module to the lower case.

Step

Size (Quantity)

Color

Torque

M2 x L4 (1)

Black

1.6 kgf-cm

20. Remove the USB board module from the lower case.

Removing the Audio Board Module

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10. See “Removing the Middle Cover” on page 73.

11. See “Removing the Power Board” on page 74.

12. See “Removing the Heatsink Fan Module” on page 75.

13. See “Removing the CPU and VGA Heatsink Module” on page 76.

14. See “Removing the CPU” on page 77.

15. See “Removing the VGA Board (Discrete Model only)” on page 78.

16. See “Removing the LCD Module” on page 79.

17. See “Separating the Upper Case from the Lower Case” on page 81.

Chapter 3

18. Disconnect the cable from the audio board module and remove it from the subwoofer (the cable is glued

to the subwoofer).

19. Release the audio board module from the latch and remove the audio board module from the lower case.

Chapter 3

Removing the Subwoofer and the Bluetooth Modules

See “Removing the Battery Pack” on page 60.

See “Removing the SD dummy card” on page 61.

See “Removing the ExpressCard dummy card” on page 61.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Hard Disk Drive Module” on page 66.

See “Removing the Keyboard” on page 72.

10.

See “Removing the Middle Cover” on page 73.

11.

See “Removing the Power Board” on page 74.

12.

See “Removing the Heatsink Fan Module” on page 75.

13.

See “Removing the CPU and VGA Heatsink Module” on page 76.

14.

See “Removing the CPU” on page 77.

15.

See “Removing the VGA Board (Discrete Model only)” on page 78.

16.

See “Removing the LCD Module” on page 79.

17.

See “Separating the Upper Case from the Lower Case” on page 81.

18.

See “Removing the Audio Board Module” on page 98.

19.

Release the subwoofer module from the latch and remove the subwoofer module from the lower case.

100

Chapter 3

20. Remove the bluetooth module from the lower case.

Chapter 3

101

LCD Module Disassembly Process

LCD Module Disassembly Flowchart

LCD MODULE DISASSEMBLY

LCD MODULE

Bx4

LCD BEZEL

Bx5

LCD ASSEMBLY

Cx3

LCD BACK PANEL

LCD FPC

LEFT LCD

RIGHT LCD

CABLE

BRACKET

ANTENNAS

VGA

CAMERA

Screw List

Item

Screw

Color

Part No.

M2.5 x L6

Black

86.00E12.536

M2 x L3

Black

86.9A522.3R0

102

Chapter 3

Removing the LCD Bezel

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Keyboard” on page 72.

See “Removing the Middle Cover” on page 73.

See “Removing the LCD Module” on page 79.

Remove the four screw covers from the LCD bezel.

10. Remove the four screws (B) on the LCD module as shown.

Step

Size (Quantity)

Color

Torque

1~4

M2.5 x L6 (4)

Black

3.0 kgf-cm

11. Carefully pry open the LCD bezel and place the bezel on top of the LCD panel.

Chapter 3

103

WARNING:Be careful when trying to lift up the LCD bezel. The top of the LCD bezel is glued to the LCD

module.

12. Disconnect the microphone cable and remove the bezel from the LCD panel.

Removing the LCD module with the Brackets

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Keyboard” on page 72.

See “Removing the Middle Cover” on page 73.

104

Chapter 3

See “Removing the LCD Module” on page 79.

See “Removing the LCD Bezel” on page 103.

10. Disconnect the cable from the web camera.

11. Disconnect the backlight cable from the connector.

12. Remove the five screws (5 x B) securing the LCD module.

Step

Size (Quantity)

Color

Torque

1~5

M2.5 x L6 (5)

Black

3.0 kgf-cm

Chapter 3

105

13. Remove the LCD with the brackets from the back cover.

Removing the FPC Cable

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the DIMM” on page 63.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the TV Tuner Board Modules” on page 64.

See “Removing the Keyboard” on page 72.

See “Removing the Middle Cover” on page 73.

See “Removing the LCD Module” on page 79.

See “Removing the LCD Bezel” on page 103.

10. See “Removing the LCD module with the Brackets” on page 104.

11. Disconnect the cables from the inverter board.

106

Chapter 3

12. Detach any adhesive tapes and any cable that is glued to the LCD panel.

13. Disconnect the FPC cable from the LCD panel.

Removing the LCD Brackets

See “Removing the Battery Pack” on page 60.

Chapter 3

107

See “Removing the Lower Cover” on page 62.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the Keyboard” on page 72.

See “Removing the Middle Cover” on page 73.

See “Removing the LCD Module” on page 79.

See “Removing the LCD Bezel” on page 103.

See “Removing the LCD module with the Brackets” on page 104.

See “Removing the FPC Cable” on page 106.

10. Remove the six screws (6 x C) securing the left and right LCD brackets to remove the brackets.

Step

Size (Quantity)

Color

Torque

1~6

M2 x L4 (6)

Silver

1.6 kgf-cm

Removing the Antennas

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the Keyboard” on page 72.

See “Removing the Middle Cover” on page 73.

See “Removing the LCD Module” on page 79.

See “Removing the LCD Bezel” on page 103.

See “Removing the LCD module with the Brackets” on page 104.

Release the antenna cables from the aluminium tapes.

108

Chapter 3

10. Remove the tapes together holding the antenna in place.

11. Remove the antenna cables from the back cover.

NOTE: There is no need to remove the antenna unless you really need to replace it.

Removing the Web Camera

See “Removing the Battery Pack” on page 60.

See “Removing the Lower Cover” on page 62.

See “Removing the WLAN Board Modules” on page 63.

See “Removing the Keyboard” on page 72.

See “Removing the Middle Cover” on page 73.

See “Removing the LCD Module” on page 79.

See “Removing the LCD Bezel” on page 103.

See “Removing the LCD module with the Brackets” on page 104.

Chapter 3

109

Remove the Web camera from the back cover.

110

Chapter 3

Chapter 4

Troubleshooting

Use the following procedure as a guide for computer problems.

NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or

modified options can give false errors and invalid system responses.

Obtain the failing symptoms in as much detail as possible.

Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating

the same operation.

Use the following table with the verified symptom to determine which page to go to.

Symptoms (Verified)

Go To

Power failure. (The power indicator does

“Power System Check” on page 113.

not go on or stay on.)

POST does not complete. No beep or error

“Power-On Self-Test (POST) Error

codes are indicated.

Message” on page 116

“Undetermined Problems” on page 130

POST detects an error and displayed

“Error Message List” on page 117

messages on screen.

Other symptoms (i.e. LCD display problems

“Power-On Self-Test (POST) Error

or others).

Message” on page 116

Symptoms cannot be re-created

Use the customer-reported symptoms and

(intermittent problems).

go to “Power-On Self-Test (POST) Error

Message” on page 116

“Intermittent Problems” on page 129

“Undetermined Problems” on page 130

Chapter 4

111

System Check Procedures

External Diskette Drive Check

Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is

required.

NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause

damage to the drive or cause the drive to fail.

Do the following to select the test device.

Boot from the diagnostics diskette and start the diagnostics program.

See if FDD Test is passed as the program runs to FDD Test.

Follow the instructions in the message window.

If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.

If the error still remains:

Reconnect the external diskette drive/DVD-ROM module.

Replace the external diskette drive/CD-ROM module.

Replace the main board.

External CD-ROM Drive Check

Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does

not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.

Do the following to select the test device:

Boot from the diagnostics diskette and start the diagnostics program.

See if CD-ROM Test is passed when the program runs to CD-ROM Test.

Follow the instructions in the message window.

If an error occurs, reconnect the connector on the System board. If the error still remains:

Reconnect the external diskette drive/CD-ROM module.

Replace the external diskette drive/CD-ROM module.

Replace the main board.

Keyboard or Auxiliary Input Device Check

Remove the external keyboard if the internal keyboard is to be tested.

If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable

extending from the keyboard is correctly seated in the connector on the system board.

If the keyboard cable connection is correct, run the Keyboard Test.

If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a

non-defective FRU:

Reconnect the keyboard cables.

Replace the keyboard.

Replace the main board.

The following auxiliary input devices are supported by this computer:

Numeric keypad

112

Chapter 4

External keyboard

If any of these devices do not work, reconnect the cable connector and repeat the failing operation.

Memory check

Memory errors might stop system operations, show error messages on the screen, or hang the system.

Boot from the diagnostics diskette and start the diagnostic program (please refer to main board.

Go to the diagnostic memory in the test items.

Press F2 in the test items.

Follow the instructions in the message window.

NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.

Power System Check

To verify the symptom of the problem, power on the computer using each of the following power sources:

Remove the battery pack.

Connect the power adapter and check that power is supplied.

Disconnect the power adapter and install the charged battery pack; then check that power is supplied by

the battery pack.

If you suspect a power problem, see the appropriate power supply check in the following list:

“Check the Power Adapter” on page 114

“Check the Battery Pack” on page 115

Chapter 4

113

Check the Power Adapter

Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power

adapter cable. See the following figure

Pin 1: +19 to +20.5V

Pin 2: 0V, Ground

If the voltage is not correct, replace the power adapter.

If the voltage is within the range, do the following:

Replace the System board.

If the problem is not corrected, see “Undetermined Problems” on page 130.

If the voltage is not correct, go to the next step.

NOTE: An audible noise from the power adapter does not always indicate a defect.

If the power-on indicator does not light up, check the power cord of the power adapter for correct

continuity and installation.

If the operational charge does not work, see “Check the Battery Pack” on page 115.

114

Chapter 4

Check the Battery Pack

To check the battery pack, do the following:

From Software:

Check out the Power Management in control Panel

In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total

Battery Power Remaining are correct.

Repeat the steps 1 and 2, for both battery and adapter.

This helps you identify first the problem is on recharging or discharging.

From Hardware:

Power off the computer.

Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).

If the voltage is still less than 7.5 Vdc after recharging, replace the battery.

To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%

of the total power remaining when installed in the computer.

If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.

Re-install the battery pack.

If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light

up, replace the DC/DC charger board.

Touchpad Check

If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a

non-defective FRU:

Reconnect the touchpad cables.

Replace the touchpad.

Replace the system board.

After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement

can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware

problem. No service actions are necessary if the pointer movement stops in a short period of time.

Chapter 4

115

Power-On Self-Test (POST) Error Message

The POST error message index lists the error message and their possible causes. The most likely cause is

listed first.

NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU

replacement does not solve the problem, put the original part back in the computer. Do not replace a

non-defective FRU.

This index can also help you determine the next possible FRU to be replaced when servicing a computer.

If the symptom is not listed, see “Undetermined Problems” on page 130.

The following lists the error messages that the BIOS displays on the screen and the error symptoms classified

by function.

NOTE: Most of the error messages occur during POST. Some of them display information about a hardware

device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the

way it has been configured.

NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter

Setup and install Setup defaults or correct the error.

116

Chapter 4

Index of Error Messages

Error Code List

Error Codes

Error Messages

006

Equipment Configuration Error

Causes:

1. CPU BIOS Update Code Mismatch

2. IDE Primary Channel Master Drive Error

(THe causes will be shown before “Equipment

Configuration Error”)

010

Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)

070

Real Time Clock Error

071

CMOS Battery Bad

072

CMOS Checksum Error

110

System disabled.

Incorrect password is specified.

Battery critical LOW

In this situation BIOS will issue 4 short beeps then shut

down system, no message will show.

Thermal critical High

In this situation BIOS will shut down system, not show

message.

Error Message List

Error Messages

FRU/Action in Sequence

Failure Fixed Disk

Reconnect hard disk drive connector.

“Load Default Settings” in BIOS Setup Utility.

Hard disk drive

System board

Stuck Key

see “Keyboard or Auxiliary Input Device Check” on page 112.

Keyboard error

see “Keyboard or Auxiliary Input Device Check” on page 112.

Keyboard Controller Failed

see “Keyboard or Auxiliary Input Device Check” on page 112.

Keyboard locked - Unlock key switch

Unlock external keyboard

Monitor type does not match CMOS - Run

Run “Load Default Settings” in BIOS Setup Utility.

Setup

Shadow RAM Failed at offset: nnnn

BIOS ROM

System board

System RAM Failed at offset: nnnn

DIMM

System board

Extended RAM Failed at offset: nnnn

DIMM

System board

System battery is dead - Replace and run

Replace RTC battery and Run BIOS Setup Utility to

Setup

reconfigure system time, then reboot system.

System CMOS checksum bad - Default

RTC battery

configuration used

Run BIOS Setup Utility to reconfigure system time, then

reboot system.

Chapter 4

117

Error Message List

Error Messages

FRU/Action in Sequence

System timer error

RTC battery

Run BIOS Setup Utility to reconfigure system time, then

reboot system.

System board

Real time clock error

RTC battery

Run BIOS Setup Utility to reconfigure system time, then

reboot system.

System board

Previous boot incomplete - Default

Run “Load Default Settings” in BIOS Setup Utility.

configuration used

RTC battery

System board

Memory size found by POST differed from

Run “Load Default Settings” in BIOS Setup Utility.

CMOS

DIMM

System board

Diskette drive A error

Check the drive is defined with the proper diskette type in

BIOS Setup Utility

See “External Diskette Drive Check” on page 112.

Incorrect Drive A type - run SETUP

Check the drive is defined with the proper diskette type in

BIOS Setup Utility

System cache error - Cache disabled

System board

CPU ID:

System board

DMA Test Failed

DIMM

System board

Software NMI Failed

DIMM

System board

Fail-Safe Timer NMI Failed

DIMM

System board

Device Address Conflict

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Allocation Error for device

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Failing Bits: nnnn

DIMM

BIOS ROM

System board

Fixed Disk n

None

Invalid System Configuration Data

BIOS ROM

System board

I/O device IRQ conflict

Run “Load Default Settings” in BIOS Setup Utility.

RTC battery

System board

Operating system not found

Enter Setup and see if fixed disk and drive A: are properly

identified.

Diskette drive

Hard disk drive

System board

118

Chapter 4

Error Message List

No beep Error Messages

FRU/Action in Sequence

No beep, power-on indicator turns off and

Power source (battery pack and power adapter). See “Power

LCD is blank.

System Check” on page 113..

Ensure every connector is connected tightly and correctly.

Reconnect the DIMM.

LED board.

System board.

No beep, power-on indicator turns on and

Power source (battery pack and power adapter). See “Power

LCD is blank.

System Check” on page 113..

Reconnect the LCD connector

Hard disk drive

LCD inverter ID

LCD cable

LCD Inverter

LCD

System board

No beep, power-on indicator turns on and

Reconnect the LCD connectors.

LCD is blank. But you can see POST on an

LCD inverter ID

external CRT.

LCD cable

LCD inverter

LCD

System board

No beep, power-on indicator turns on and a

Ensure every connector is connected tightly and correctly.

blinking cursor shown on LCD during

System board

POST.

No beep during POST but system runs

Speaker

correctly.

System board

Chapter 4

119

Phoenix BIOS Beep Codes

Code

Beeps

POST Routine Description

02h

Verify Real Mode

03h

Disable Non-Maskable Interrupt (NMI)

04h

Get CPU type

06h

Initialize system hardware

08h

Initialize chipset with initial POST values

09h

Set IN POST flag

0Ah

Initialize CPU registers

0Bh

Enable CPU cache

0Ch

Initialize caches to initial POST values

0Eh

Initialize I/O component

0Fh

Initialize the local bus IDE

10h

Initialize Power Management

11h

Load alternate registers with initial POST

values

12h

Restore CPU control word during warm

boot

13h

Initialize PCI Bus Mastering devices

14h

Initialize keyboard controller

16h

1-2-2-3

BIOS ROM checksum

17h

Initialize cache before memory autosize

18h

8254 timer initialization

1Ah

8237 DMA controller initialization

1Ch

Reset Programmable Interrupt Controller

20h

1-3-1-1

Test DRAM refresh

22h

1-3-1-3

Test 8742 Keyboard Controller

24h

Set ES segment register to 4 GB

26h

Enable A20 line

28h

Autosize DRAM

29h

Initialize POST Memory Manager

2Ah

Clear 215 KB base RAM

2Ch

1-3-4-1

RAM failure on address line xxxx

2Eh

1-3-4-3

RAM failure on data bits xxxx of low byte

of memory bus

2Fh

Enable cache before system BIOS

shadow

30h

1-4-1-1

RAM failure on data bits xxxx of high byte

of memory bus

32h

Test CPU bus-clock frequency

33h

Initialize Phoenix Dispatch Manager

36h

Warm start shut down

38h

Shadow system BIOS ROM

3Ah

Autosize cache

120

Chapter 4

Code

Beeps

POST Routine Description

3Ch

Advanced configuration of chipset

registers

3Dh

Load alternate registers with CMOS

values

42h

Initialize interrupt vectors

45h

POST device initialization

46h

2-1-2-3

Check ROM copyright notice

48h

Check video configuration against CMOS

49h

Initialize PCI bus and devices

4Ah

Initialize all video adapters in system

4Bh

QuietBoot start (optional)

4Ch

Shadow video BIOS ROM

4Eh

Display BIOS copyright notice

50h

Display CPU type and speed

51h

Initialize EISA board

52h

Test keyboard

54h

Set key click if enabled

58h

2-2-3-1

Test for unexpected interrupts

59h

Initialize POST display service

5Ah

Display prompt “Press F2 to enter

SETUP”

5Bh

Disable CPU cache

5Ch

Test RAM between 512 and 640 KB

60h

Test extended memory

62h

Test extended memory address lines

64h

Jump to User Patch1

66h

Configure advanced cache registers

67h

Initialize Multi Processor APIC

68h

Enable external and CPU caches

69h

Setup System Management Mode (SMM)

area

6Ah

Display external L2 cache size

6Bh

Load custom defaults (optional)

6Ch

Display shadow-area message

6Eh

Display possible high address for UMB

recovery

70h

Display error messages

72h

Check for configuration errors

76h

Check for keyboard errors

7Ch

Set up hardware interrupt vectors

7Eh

Initialize coprocessor if present

80h

Disable onboard Super I/O ports and

IRQs

81h

Late POST device initialization

Chapter 4

121

Code

Beeps

POST Routine Description

82h

Detect and install external RS232 ports

83h

Configure non-MCD IDE controllers

84h

Detect and install external parallel ports

85h

Initialize PC-compatible PnP ISA devices

86h

Re-initialize onboard I/O ports

87h

Configure Motherboard Configurable

Devices (optional)

88h

Initialize BIOS Area

89h

Enable Non-Maskable Interrupts (NMIs)

8Ah

Initialize Extended BIOS Data Area

8Bh

Test and initialize PS/2 mouse

8Ch

Initialize floppy controller

8Fh

Determine number of ATA drives

(optional)

90h

Initialize hard-disk controllers

91h

Initialize local-bus hard-disk controllers

92h

Jump to UserPatch2

93h

Build MPTABLE for multi-processor

boards

95h

Install CD ROM for boot

96h

Clear huge ES segment register

97h

Fixup Multi Processor table

98h

1-2

Search for option ROMs. One long, two

short beeps on checksum failure.

99h

Check for SMART drive (optional)

9Ah

Shadow option ROMs

9Ch

Set up Power Management

9Dh

Initialize security engine (optional)

9Eh

Enable hardware interrupts

9Fh

Determine number of ATA and SCSI

drives

A0h

Set time of day

A2h

Check key lock

A4h

Initialize Typematic rate

A8h

Erase F2 prompt

AAh

Scan for F2 key stroke

ACh

Enter SETUP

AEh

Clear Boot flag

B0h

Check for errors

B2h

POST done- prepare to boot operating

system

B4h

One short beep before boot

B5h

Terminate QuietBoot (optional)

B6h

Check password (optional)

122

Chapter 4

Code

Beeps

POST Routine Description

B9h

Prepare Boot

BAh

Initialize DMI parameters

BBh

Initialize PnP Option ROMs

BCh

Clear parity checkers

BDh

Display MultiBoot menu

BEh

Clear screen (optional)

BFh

Check virus and backup reminders

C0h

Try to boot with INT 19

C1h

Initialize POST Error Manager (PEM)

C2h

Initialize error logging

C3h

Initialize error display function

C4h

Initialize system error handler

C5h

PnPnd dual CMOS (optional)

C6h

Initialize notebook docking (optional)

C7h

Initialize notebook docking late

C8h

Force check (optional)

C9h

Extended checksum (optional)

D2h

Unknown interrupt

Code

Beeps

E0h

Initialize the chipset

E1h

Initialize the bridge

E2h

Initialize the CPU

E3h

Initialize the system timer

E4h

Initialize system I/O

E5h

Check force recovery boot

E6h

Checksum BIOS ROM

E7h

Go to BIOS

E8h

Set Huge Segment

E9h

Initialize Multi Processor

EAh

Initialize OEM special code

EBh

Initialize PIC and DMA

ECh

Initialize Memory type

EDh

Initialize Memory size

EEh

Shadow Boot Block

EFh

System memory test

F0h

Initialize interrupt vectors

F1h

Initialize Run Time Clock

F2h

Initialize video

F3h

Initialize System Management Mode

F4h

Output one beep before boot

Chapter 4

123

Code

Beeps

F5h

Boot to Mini DOS

F6h

Clear Huge Segment

F7h

Boot to Full DOS

124

Chapter 4

Index of Symptom-to-FRU Error Message

LCD-Related Symptoms

Symptom / Error

Action in Sequence

LCD backlight doesn't work

Enter BIOS Utility to execute “Load Setup Default Settings”,

LCD is too dark

then reboot system.

LCD brightness cannot be adjusted

Reconnect the LCD connectors.

LCD contrast cannot be adjusted

Keyboard (if contrast and brightness function key doesn't

work).

LCD inverter ID

LCD cable

LCD inverter

LCD

System board

Unreadable LCD screen

Reconnect the LCD connector

Missing pels in characters

LCD inverter ID

Abnormal screen

LCD cable

Wrong color displayed

LCD inverter

LCD

System board

LCD has extra horizontal or vertical lines

LCD inverter ID

displayed.

LCD inverter

LCD cable

LCD

System board

Indicator-Related Symptoms

Symptom / Error

Action in Sequence

Indicator incorrectly remains off or on, but

Reconnect the inverter board

system runs correctly

Inverter board

System board

Power-Related Symptoms

Symptom / Error

Action in Sequence

Power shuts down during operation

Power source (battery pack and power adapter). See “Power

System Check” on page 113.

Battery pack

Power adapter

Hard drive & battery connection board

System board

The system doesn’t power-on.

Power source (battery pack and power adapter). See “Power

System Check” on page 113.

Battery pack

Power adapter

Hard drive & battery connection board

System board

Chapter 4

125

Power-Related Symptoms

Symptom / Error

Action in Sequence

The system doesn’t power-off.

Power source (battery pack and power adapter). See “Power

System Check” on page 113.

Hold and press the power switch for more than 4 seconds.

System board

Battery can’t be charged

See “Check the Battery Pack” on page 115.

Battery pack

System board

PCMCIA-Related Symptoms

Symptom / Error

Action in Sequence

System cannot detect the PC Card

PCMCIA slot assembly

(PCMCIA)

System board

PCMCIA slot pin is damaged.

PCMCIA slot assembly

Memory-Related Symptoms

Symptom / Error

Action in Sequence

Memory count (size) appears different from

Enter BIOS Setup Utility to execute “Load Default Settings,

actual size.

then reboot system.

DIMM

System board

Speaker-Related Symptoms

Symptom / Error

Action in Sequence

In Windows, multimedia programs, no

Audio driver

sound comes from the computer.

Speaker

System board

Internal speakers make noise or emit no

Speaker

sound.

System board

Power Management-Related Symptoms

Symptom / Error

Action in Sequence

The system will not enter hibernation

See “Save to Disk (S4)” on page 37.

Keyboard (if control is from the keyboard)

Hard disk drive

System board

The system doesn't enter hibernation mode

Press Fn+o and see if the computer enters hibernation

and four short beeps every minute.

mode.

Touchpad

Keyboard

Hard disk connection board

Hard disk drive

System board

The system doesn’t enter standby mode

See “Save to Disk (S4)” on page 37.

after closing the LCD

LCD cover switch

System board

126

Chapter 4

Power Management-Related Symptoms

Symptom / Error

Action in Sequence

The system doesn't resume from

See “Save to Disk (S4)” on page 37.

hibernation mode.

Hard disk connection board

Hard disk drive

System board

The system doesn't resume from standby

See “Save to Disk (S4)” on page 37.

mode after opening the LCD.

LCD cover switch

System board

Battery fuel gauge in Windows doesn’t go

Remove battery pack and let it cool for 2 hours.

higher than 90%.

Refresh battery (continue use battery until power off, then

charge battery).

Battery pack

System board

System hangs intermittently.

Reconnect hard disk/CD-ROM drives.

Hard disk connection board

System board

Peripheral-Related Symptoms

Symptom / Error

Action in Sequence

System configuration does not match the

Enter BIOS Setup Utility to execute “Load Default Settings”,

installed devices.

then reboot system.

Reconnect hard disk/CD-ROM/diskette drives.

External display does not work correctly.

Press Fn+F5, LCD/CRT/Both display switching

System board

USB does not work correctly

System board

Print problems.

Ensure the “Parallel Port” in the “Onboard Devices

Configuration” of BIOS Setup Utility is set to Enabled.

Onboard Devices Configuration

Run printer self-test.

Printer driver

Printer cable

Printer

System Board

Serial or parallel port device problems.

Ensure the “Serial Port” in the Devices Configuration” of

BIOS Setup Utility is set to Enabled.

Device driver

Device cable

Device

System board

Keyboard/Touchpad-Related Symptoms

Symptom / Error

Action in Sequence

Keyboard (one or more keys) does not

Reconnect the keyboard cable.

work.

Keyboard

System board

Chapter 4

127

Keyboard/Touchpad-Related Symptoms

Symptom / Error

Action in Sequence

Touchpad does not work.

Reconnect touchpad cable.

Touchpad board

System board

Modem-Related Symptoms

Symptom / Error

Action in Sequence

Internal modem does not work correctly.

Modem phone port

modem combo board

System board

NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined

Problems” on page 130.

128

Chapter 4

Intermittent Problems

Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a

hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement

should be considered only when a recurring problem exists.

When analyzing an intermittent problem, do the following:

Run the advanced diagnostic test for the system board in loop mode at least 10 times.

If no error is detected, do not replace any FRU.

If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

Chapter 4

129

Undetermined Problems

The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,

whether a short circuit is suspected, or whether the system is inoperative.

Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).

NOTE: Verify that all attached devices are supported by the computer.

NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power

System Check” on page 113.):

Power-off the computer.

Visually check them for damage. If any problems are found, replace the FRU.

Remove or disconnect all of the following devices:

Non-Acer devices

Printer, mouse, and other external devices

Battery pack

Hard disk drive

DIMM

CD-ROM/Diskette drive Module

PC Cards

Power-on the computer.

Determine if the problem has changed.

If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:

System board

LCD assembly

130

Chapter 4

Chapter 5

Jumper and Connector Locations

Top and Bottom View

Chapter 5

131

132

Chapter 5

Clearing Password Check and BIOS Recovery

This section provide you the standard operating procedures of clearing password and BIOS recovery for

Aspire 5930/5930Z/5730Z Series. Aspire 5930/5930Z/5730Z Series provide one Hardware Open Gap on main

board for clearing password check, and one Hotkey for enabling BIOS Recovery.

Clearing Password Check

Hardware Open Gap Description

Hardware

Default Setting

Operation Description

Gap

Open (Normal)

Short (Clearing Password Check)

HW Gap position on M/B space:

Gap name in Aspire 5930/5930Z/5730Z Series is G27

G27

Steps for Clearing BIOS Password Check

If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask

the password during systems POST or when systems enter to BIOS Setup menu. However, once it is

necessary to bypass the password check, users need to short the HW Gap to clear the password by the

following steps:

•

Power Off a system, and remove HDD, AC and Battery from the machine.

•

Open the back cover of the machine, and find out the HW Gap on M/B as picture.

•

Use an electric conductivity tool to short the two points of the HW Gap.

•

Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the

system till BIOS POST finish. Then remove the tool from the HW Gap.

•

Restart system. Press F2 key to enter BIOS Setup menu.

•

If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and

try again.

NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).

Chapter 5

133

BIOS Recovery by Crisis Disk

BIOS Recovery Boot Block:

BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS

initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous

BIOS flashing process failed.

BIOS Recovery Hotkey:

The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered

on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery

present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot

Block.

Steps for BIOS Recovery by Crisis Disk:

Before doing this, one Crisis Disk should be prepared ready in hand. The Crisis Disk could be made by

executing the Crisis Disk program in another system with Windows XP OS.

Follow the steps below:

Power Off system.

Insert the Crisis Disk to a USB floppy drive which is attached to the BIOS flash failed machine.

In the power-off state, press Fn+Esc and hold them and then press Power Button. The system should be

powered on with Crisis BIOS Recovery process.

BIOS Boot Block starts to restore the BIOS code from the Crisis floppy disk to BIOS ROM on the failed

machine.

If the Crisis flashing process is finished, the system will restart.

If the Crisis Recovery process is finished, the system should be powered on with successful and workable

BIOS. Then a person can update the latest version BIOS for this machine by regular BIOS flashing process.

134

Chapter 5

Chapter 6

FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of 5930/5930Z/5730Z Series. Refer

to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your

regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service

Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from

those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer

office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to

dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Chapter 6

135

Aspire 5930/5930Z/5730Z Series Exploded Diagram

136

Chapter 6

Chapter 6

137

Aspire 5930/5930Z/5730Z Series FRU List

Category

No.

Part Name and Description

Acer Part No.

ACCESSORY

REMOTE CONTROLLER FORMOSA21

RT.22700.011

RC804V-B EN

REMOTE CONTROLLER FORMOSA21

RT.22700.008

RC804V-B EU

Adapter

ADAPTER 90W LITEON PA-1900-24AR

AP.09003.011

ADAPTER 90W DELTA ADP-90SB

AP.09001.013

BBEA LF

ADAPTER 90W 3PIN DELTA ADP-

AP.09001.014

90SB

ADT 90W 19V 3P HP-OL093B13P LF

AP.0900A.001

ADAPTER 65W 3PIN DELTA SADP-

AP.06501.014

65KB BFJA LF

ADAPTER 65W LITEON PA-1650-02AC

AP.06503.016

ADAPTER 65W HIPRO HP-OK065B13

AP.0650A.010

ADAPTER 65W DELTA SADP-65KB

AP.06501.013

DFA LF

Battery-

SANYO AS-2007B LI-ION 3S2P SANYO

BT.00603.042

6 CELL 4400MAH

SONY AS-2007B LI-ION 3S2P SONY 6

BT.00604.025

CELL 4400MAH

PANASONIC AS-2007B LI-ION 3S2P

BT.00605.021

PANASONIC 6 CELL 4400MAH

SIMPLO AS-2007B LI-ION 3S2P

BT.00607.016

PANASONIC 6 CELL 4400MAH

SIMPLO AS-2007B LI-ION 4S2P

BT.00807.015

PANASONIC 8 CELL 4800MAH

Boards

EIGER AUDIO BD 07629-2M (D)

55.AR501.001

EIGER PD E KEY BD (D)

55.AR501.006

EIGER PD LAUNCH BD (D)

55.AR501.002

EIGER PD POWER BD (D)

55.AR501.007

EIGER PD USB BD WITH TV (D)

55.AQE01.001

TOUCHPAD SYNAPTICS TM00540-001

56.AGV01.001

BT MOD FOXCONN BCM2045 V2

BT.21100.005

WLAN 802.11ABGN SHIRLEYPEAK1*2

KI.SPM01.003

VGA MXM CARD NVIDIA 9PGSHM

55.AQ301.001

DDRIII 512MB W/HDCP (MSI MADE)

VGA CARD NB9P-GS/512M GDDR3

BIWA MINI SENSOR BD 07522-2M

55.TKJ01.001

EIGER PD FP BD WITH MINI (D)

55.AQ301.002

138

Chapter 6

Category

No.

Part Name and Description

Acer Part No.

TV TUNCER DVB-T MINI TT-1260DA

TU.23100.015

CAPACITIVE BUTTON TM-01119-001

55.AR501.005

MODEM BOARD FOXCONN DELPHI-

FX.22500.022

AM5 V2H 1.5_3.3V

Cables

LAUNCH BOARD CABLE

50.AR501.002

MEDIA BOARD CABLE

50.AR501.005

TOUCHPAD BOARD CABLE

50.AR501.006

USB BOARD CABLE

50.AR501.003

BLUETOOTH BOARD CABLE

50.AR501.007

AUDIO BOARD CABLE

50.AR501.001

DC-IN CABLE 90W

50.AQ301.001

TV TUNER BOARD CABLE

50.AQE01.001

TOUCHPAD BUTTON BOARD CABLE

50.AR501.004

DC-IN CABLE 65W

50.AR501.008

LCD/CAMERA CABLE 15.4" WXGA

50.AR501.009

POWER CORD 10A 125V US

27.T30V1.001

POWER CORD 10A 125V 3PIN US BK

27.01518.641

POWER CORD 2.5A 125V 8121- USA/

27.01518.781

W CNS

POWER CORD 220V 3PIN EUR

27.T30V1.004

POWER CABLE 16A 250V 3PIN EUR

27.01518.731

POWER CORD 3A 250V 3PIN UK

27.01518.541

POWER CORD 5A 250V 3PIN UK BK

27.03118.001

POWER CORD 10A 3PIN BK

27.01518.561

DENMARK

POWER CORD 10A 250V 3PIN

27.01518.671

DENMARK BK

POWER CORD 10A 250V 3PIN BK

27.01518.571

SOUTH AFRICA

POWER CORD 16A 250V SOUTH

27.01518.681

AFRICA BK

POWER CORD 10A 250V SWISS

27.01518.581

POWER CORD 10A 250V 3PIN SWISS

27.01518.691

POWER CORD 10A 250V 3PIN CHINA

27.01518.591

POWER CORD 10A 250V 3PIN CHINA

27.01518.701

POWER CORD 10A 250V 3PIN ITALY

27.01518.611

POWER CORD 10A 250V 3PIN ITALY

27.01518.711

POWER CORD 2.5A 250V SOUTH

27.01518.631

AFRICA BK (INDIA)

POWER CORD 10A 250V SOUTH

27.01518.721

AFRICA BK (INDIA)

POWER CORD 2.5A 250V AUSTRALIA

27.01518.621

POWER CORD ACA/ACNZ

27.03218.021

POWER CORD 7A 125V 2PIN JAPEN

27.01518.551

POWER CORD 7A 125V 2PIN JAPAN

27.03518.161

Chapter 6

139

Category

No.

Part Name and Description

Acer Part No.

POWER CORD 7A 250V 2PIN KOREA

27.01518.531

POWER CORD 250V 10A 3PIN ISRAEL

27.01518.761

Case/Cover/Bracket/Assembly

LOWER CASE W/MODEM CABLE&FAN

60.AQE01.001

BRACKET&SPEAKER FOR TV

SPEAKER SUB WOFFER

23.AR501.001

SPEAKER SET

23.AR501.002

EXPRESS DUMMY CARD

42.AR501.004

NEW CARD DUMMY CARD

42.TK901.005

SD DUMMY CARD

42.TK901.006

MIDDLE COVER

42.AR501.001

UNITLOAD COVER

42.AR501.002

E-KEY COVER

42.AR501.003

TOUCHPAD BRACKET

33.AR501.001

VGA BOARD BARCKET FOR NVIDIA

33.TPE01.001

UPPER CASE W/SPEAKER&E KEY

60.AQ301.002

CABLE&POWER

CABLE&FINGERPRINT HOLE

OPTICAL BRACKET

33.AR501.002

BD COMBO BEZEL

42.AR501.005

SUPER MULIT BEZEL

42.AGV01.005

HDD BRACKET

33.AR501.003

LCD COVER 15.4" W/BACKLIGHT

60.AR501.005

MODULE&ANTENNA

LCD BEZEL 15.4" W/MICROPHONE

60.AR501.004

LCD BRACKET W/HINGE LEFT

33.AR501.004

LCD BRACKET W/HINGE RIGHT

33.AR501.005

Combo Module

COMBO MODULE BLU-RAY 2X

6M.AR501.001

ODD SONY BD COMBO 12.7MM TRAY

KO.0020E.002

DL 2X BC-5500S LF W/O BEZEL SATA

Communication Module

EXTERNAL ANTENNA SET

25.AQE01.001

CPU/Processor

140

Chapter 6

Category

No.

Part Name and Description

Acer Part No.

CPU INTEL CORE2DUAL P8400 PGA

KC.84001.DPP

2.26G 3M 1066 25W

CPU INTEL CORE2DUAL P8600 PGA

KC.86001.DPP

2.4G 1066 25W 3M

CPU INTEL CORE2DUAL P9500 PGA

KC.95001.DPP

2.53G 6M 1066 25W

CPU INTEL CORE2DUAL T9400 PGA

KC.94001.DTP

2.53G 6M 1066 35W

CPU INTEL CORE2DUAL T9600 PGA

KC.96001.DTP

2.8G 6M 1066 35W

DVD Module

ODD TOSHIBA SUPER-MULTI DRIVE

KU.00801.021

12.7MM TRAY DL 8X TS-L633A LF W/O

BEZEL SATA

ODD PIONEER SUPER-MULTI DRIVE

KU.00805.044

12.7MM TRAY DL 8X DVR-TD08RS LF

W/O BEZEL SATA

ODD PANASONIC SUPER-MULTI

KU.00807.059

DRIVE 12.7MM TRAY DL 8X UJ-870A

LF W/O BEZEL SATA

ODD HLDS SUPER-MULTI DRIVE

KU.0080D.029

12.7MM TRAY DL 8X GSA-T50N LF W/

O BEZEL SATA

ODD HLDS SUPER-MULTI DRIVE

KU.0080D.034

12.7MM TRAY DL 8X GSA-T50N LF W/

O BEZEL SATA MALAYSIA

ODD SONY SUPER-MULTI DRIVE

KU.0080E.009

12.7MM TRAY DL 8X AD-7560S LF W/O

BEZEL SATA

ODD PLDS SUPER-MULTI DRIVE

KU.0080F.001

12.7MM TRAY DL 8X DS-8A2S LF W/O

BEZEL SATA

Fan

FAN SUNON

23.AR501.003

Heatsink

CPU HEATSINK AVC NB9 W/O FAN

60.AQ301.003

HDD/Hard Disk Drive

Chapter 6

141

Category

No.

Part Name and Description

Acer Part No.

HDD 120GB 5400RPM SATA II HGST

KH.12007.014

HTS542512K9SA00 BRONCO-B LF

HDD 120GB 5400RPM SATA SEAGATE

KH.12001.032

ST9120817AS LF

HDD 120GB 5400RPM SATA TOSHIBA

KH.12004.007

MK1246GSX LF

HDD 120GB 5400RPM SATA WD

KH.12008.019

WD1200BEVS-22UST0 ML125 LF

HDD 160GB WD WD1600BEVT-22ZCT0

KH.16008.022

HDD 160GB 5400RPM SATA II HITACHI

KH.16007.016

HTS541616J9SA00 LF

HDD 160GB SEAGATE SATA

KH.16001.029

ST9160827AS

HDD 160GB 5400RPM SATA TOSHIBA

KH.16004.002

MK1646GSX LF

HDD 250GB SEAGATE SATA

KH.25001.011

ST9250827AS

HDD 250GB 5400RPM SATA TOSHIBA

KH.25004.001

MK2546GSX LF

HDD 250GB 5400RPM SATA II HGST

KH.25007.011

HTS542525K9SA00 LF

HDD 250GB 5400RPM SATA WD

KH.25008.018

WD2500BEVS-22UST0 ML125

HDD 320GB 5400RPM SATA WD

KH.32008.013

WD3200BEVT-22ZCT0 ML125

Keyboard

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.442

E88KS US INTERNATIONAL (ASPIRE

BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.443

E88KS US INTERNATIONAL HEBREW

(ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.444

E89KS UK (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.445

E89KS TURKISH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.446

E88KS THAILAND (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.447

E89KS SWISS/G (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.448

E89KS SWEDISH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.449

E89KS SPANISH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.451

89KS SLO/CRO (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.452

E88KS RUSSIAN (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.453

E89KS PORTUGUESE (ASPIRE

BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.454

E89KS POLISH (ASPIRE BLACK)

142

Chapter 6

Category

No.

Part Name and Description

Acer Part No.

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.455

E89KS NORWEGIAN (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.457

E88KS KOREAN (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.458

E93KS JAPANESE (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.459

E89KS ITALIAN (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.462

E89KS HUNGARIAN (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.463

E88KS GREEK (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.464

E89KS GERMAN (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.465

E89KS FRENCH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.467

E89KS DUTCH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.468

E89KS DANISH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.469

E89KS CZECH (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.470

E88KS TRADITIONAL CHINESE

(ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.471

E89KS CANADIAN FRENCH (ASPIRE

BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.472

E89KS BRAZILIAN PORTUGUESE

(ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.473

E89KS BELGIUM (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.474

E88KS ARABIC/ENGLISH (ASPIRE

BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.475

E89KS ARABIC/FRENCH (ASPIRE

BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.476

E89KS NORDIC (ASPIRE BLACK)

KEYBOARD 14_15KB-FV3 BLACK

KB.INT00.477

E89KS ENGLISH/CANADIAN FRENCH

(ASPIRE BLACK)

LCD Module

LCD CMO 15.4" WXGA GLARE N154I3-

LK.1540D.022

L03 LF 220NIT 8MS

LCD AUO 15.4" WXGA GLARE

LK.15405.028

B154EW02-V7 W/O BRACKET, H/W

CODE 3A LF 220NIT 8MS

LCD AUO 15.4" WXGA GLARE

LK.15405.029

B154EW08-V1 W/O BRACKET, HW 3A

LF 220NIT 8MS

LCD LPL 15.4" WXGA GLARE

LK.15408.029

LP154WX4-TLB4 LF 220NIT 8MS

Chapter 6

143

Category

No.

Part Name and Description

Acer Part No.

MAINBOARD

MAINBOARD AS5930G INTEL LF

MB.AQ201.001

PGM45 ICH9 LF FOR MONTEVINA

CPU WITH PR_ESATA

MAINBOARD AS5930 INTEL LF GM45

MB.AR501.001

ICH9 LF FOR MONTEVINA CPU WITH

PR_ESATA

MEMORY

SODIMM 1GB DDRII667 HYNIX

KN.1GB0G.012

HYMP112S64CP6-Y5 LF

SODIMM 1GB DDRII667 SAMSUNG

KN.1GB0B.016

M470T2864QZ3-CE6

SODIMM 1GB DDRII667 INFINEON

KN.1GB02.036

HYS64T128021EDL-3S LF

SODIMM 1GB DDRII667 NANYA

KN.1GB03.014

NT1GT64U8HB0BN-3C LF (0.09U)

SODIMM 2GB DDRII667 ELPIDA

KN.2GB09.001

EBE21UE8ACUA-6E-E LF

SODIMM 2GB DDRII667 HYNIX

KN.2GB0G.004

HYMP125S64CP8-Y5 LF

SODIMM 2GB DDRII667 SAMSUNG

KN.2GB0B.003

M470T5663QZ3-CE6 LF

SODIMM 2GB DDRII667 MICRON

KN.2GB04.001

MT16HTF25664HY-667E1 LF

SODIMM 512MB DDRII667 HYNIX

KN.5120G.024

HYMP164S64CP6-Y5 LF

SODIMM 512MB DDRII667 NANYA

KN.51203.032

NT512T64UH8B0FN-3C LF

SODIMM 512MB DDRII667 SAMSUNG

KN.5120B.026

M470T6464QZ3-CE6 LF

MISCELLANEOUS

NAME PLATE AS5930

47.AR501.001

LOGO PLATE FOR LCD PANEL

47.AR501.002

SCREW

IMS M2X4(H=0.3)

86.00E13.524

SCREW M2*L3 NYLOK CR 3+

86.00E25.723

SCREW M2-3

86.9A522.3R0

ISO M2.5X6(H=0.7~0.8MM)

86.00E12.536

M2.5*L10 BLACK ZN

86.00F84.73A

SCREW MACH WAFER M3*L4 NI

86.9A524.4R0

144

Chapter 6

Chapter 6

145

Appendix A

Model Definition and Configuration

Aspire 5930/5930Z/5730Z Series

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

AAP

India

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSIL1

13BG

UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Indonesia

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSIN1

13BG

UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSMA

13BG

2 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Philippines

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSPH

13BG

1 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Singapore

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSSG

13BG

1 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Thailand

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSTH

13BG

2 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Vietnam

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSVN

13BG

1 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

Appendix A

146

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

USA/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Canada -

30J.00

XMi

WXGA

MBII5

GB5.4

ATH54

Canadian

MCECF

13BG

French

UMAC

2*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

USA/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Canada -

30J.00

XMi

WXGA

MBII5

GB5.4

ATH54

Canadian

MCEUS

13BG

French

UMAC

2*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Australia/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

New

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

Zealand

XPHAU1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

USA/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Canada

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHEN1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

ACLA-

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Spanish

305.01

XMi

WXGA

MBII5

GB5.4

ATH54

XPHES1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

USA/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Canada

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHFR1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Indonesia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHIN1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHMA2

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Philippines

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHPH1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

147

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

AAP

Thailand

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHTH2

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Vietnam

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHVN1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Singapore

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

305.00

XMi

WXGA

MBII5

GB5.4

ATH54

XPHWSG2

13BG

1W UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

ACLA-

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Portuguese

305.01

XMi

WXGA

MBII5

GB5.4

ATH54

XPHXC1

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

TWN

GCTWN

S2.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

FOX_

1AWX

305.00

XMi

WXGA

MBII6

GB5.4

ATH54

BRM_

XPHTC1

13BG

2.0

UMAC

2*512/120/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

TWN

GCTWN

S2.AV

AS5052WX

ATTL5

N14.1

SO512

N100

NSM8

ABT_

FOX_

2WXM

305.00

WXGA

MBII6

GB5.4

ATH54

BRM_

XPHTC1

13BG

2.0

UMAC

2*512/100/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

TWN

GCTWN

S2.AV

AS5055WX

ATTL6

N14.1

SO1G

N160

NSM8

ABT_

FOX_

5WXM

305.00

WXGA

BII5

GB5.4

BRM4

BRM_

XPHTC1

318BG

2.0

UMAC

2*1G/160/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

China

Hong Kong

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NCB2

ABT_

1AWX

305.01

XCi

WXGA

MBII5

GB5.4

ATH54

XPHHK9

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

China

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NCB2

ABT_

1AWX

305.01

XCi

WXGA

MBII5

GB5.4

ATH54

XPHSC7

13BG

UMAC

1*512/120/

6L/5R/

CB_bg_0.3

C_AN

Appendix A

148

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

TWN

GCTWN

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

FOX_

1AWX

305.01

XMi

WXGA

MBII5

GB5.4

ATH54

BRM_

XPHTC1

13BG

2.0

UMAC

1*512/120/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

TWN

GCTWN

LX.AV

AS5051AW

ATMK

N14.1

SO512

N60G

NSM8

ABT_

FOX_

1AWX

305.01

XMi

WXGA

MBII5

B5.4K

ATH54

BRM_

XPHTC1

13BG

2.0

UMAC

1*512/60/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

TWN

GCTWN

LX.AV

AS5051AW

ATMK

N14.1

SO512

N80G

NSM8

ABT_

FOX_

1AWX

305.01

XMi

WXGA

MBII5

B5.4K

ATH54

BRM_

XPHTC1

13BG

2.0

UMAC

1*512/80/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Australia/

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

New

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

Zealand

MCEAU1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Singapore

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCESG1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

India

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCEIL1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Indonesia

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCEIN1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Philippines

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCEPH1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCEMA1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

149

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

AAP

Thailand

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCETH1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Vietnam

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

30J.01

XMi

WXGA

BII6

GB5.4

ATH54

MCEVN1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Australia/

LX.AV

AS5051AW

ATMK

N14.1

SO1G

N120

NSM8

ABT_

1AWX

New

306.00

XMi

WXGA

BII6

GB5.4

ATH54

Zealand

XPPAU1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Australia/

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

New

30J.00

WXGA

BII6

GB5.4

ATH54

Zealand

MCEAU1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

India

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.00

Mi MCEIL1

WXGA

BII6

GB5.4

ATH54

UMAC

13BG

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Indonesia

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.00

Mi MCEIN1

WXGA

BII6

GB5.4

ATH54

UMAC

13BG

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Singapore

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.00

WXGA

BII6

GB5.4

ATH54

MCESG1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Philippines

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.00

WXGA

BII6

GB5.4

ATH54

MCEPH1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.00

WXGA

BII6

GB5.4

ATH54

MCEMA1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

Appendix A

150

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

AAP

Thailand

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.00

WXGA

BII6

GB5.4

ATH54

MCETH1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Vietnam

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

30J.01

WXGA

BII6

GB5.4

ATH54

MCEVN1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Australia/

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

2WXM

New

306.00

WXGA

BII6

GB5.4

ATH54

Zealand

XPPAU1

13BG

UMAC

1*1G/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

India

LX.AV

AS5051AN

ATMK

N14.1

SO256

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSIL1

13BG

UMAC

1*256/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Vietnam

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSVN

13BG

1 UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Thailand

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NSM8

ABT_

FOX_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

BRM_

XMi

LINPUSTH

13BG

2.0

2 UMAC

1*512/80/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Singapore

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSSG

13BG

1 UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

India

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSIL1

13BG

UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Indonesia

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSIN1

13BG

UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

151

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

AAP

Philippines

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSPH

13BG

1 UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSMA

13BG

2 UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Thailand

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

1ANW

30C.0

WXMi

WXGA

MBII5

B5.4K

ATH54

XMi

LINPUSTH

13BG

2 UMAC

1*512/60/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Thailand

LX.AV

AS5052WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

FOX_

2WXM

30J.01

WXGA

BII6

GB5.4

ATH54

BRM_

MCETH1

13BG

2.0

UMAC

1*1G/120/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

EMEA

Belgium

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCEBE6

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Middle

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

East

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCEAR1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Middle

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

East

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCEAR2

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Italy

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCEIT7

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Spain

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCEESJ

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

Appendix A

152

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA

Eastern

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Europe

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCECS5

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Denmark

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.02

XMi

WXGA

MBII6

GB5.4

BRM4

MCEDK6

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

France

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.02

XMi

WXGA

MBII6

GB5.4

BRM4

MCEFRF

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Germany

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.02

XMi

WXGA

MBII6

GB5.4

BRM4

MCEDEA

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Germany

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.02

XMi

WXGA

MBII6

GB5.4

BRM4

MCEDEB

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Holland

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCENL6

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Norway

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCENO5

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Russia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCERU9

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Eastern

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Europe

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCEPL7

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

153

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA

Slovenia/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Croatia

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCESI1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Portugal

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCEPT6

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Sweden/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Finland

30J.02

XMi

WXGA

MBII6

GB5.4

BRM4

MCESV5

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Turkey

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCETR5

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Switzerland

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCESW8

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCEUK5

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCEWUK1

318BG

1W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Italy

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

MCEWIT11

318BG

W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Germany

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.03

XMi

WXGA

MBII6

GB5.4

BRM4

MCEWDE1

318BG

1W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

Appendix A

154

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA

France

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

30J.02

XMi

WXGA

MBII6

GB5.4

BRM4

MCEWFR1

318BG

1W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Belgium

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.01

XMi

WXGA

MBII6

GB5.4

BRM4

XPHBE1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Middle

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

East

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHAR1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Eastern

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Europe

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHCS2

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Germany

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHDE7

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Greece

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHEL1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Israel

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHIS1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Italy

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHIT1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Denmark

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.01

XMi

WXGA

MBII6

GB5.4

BRM4

XPHDK1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

155

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA

Holland

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHNL1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

France

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHFRA

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Eastern

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Europe

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHHU6

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Spain

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHESA

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Slovenia/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Croatia

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHSLO2

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Eastern

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Europe

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHPL6

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Portugal

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHPT1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Switzerland

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHSW5

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Turkey

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHTR1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

Appendix A

156

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA

South

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Africa

305.01

XMi

WXGA

MBII6

GB5.4

BRM4

XPHSA1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Norway

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHNO1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Russia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHRU2

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Sweden/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

Finland

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHSV1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

France

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.02

XMi

WXGA

MBII6

GB5.4

BRM4

XPHWFRB

318BG

1W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Italy

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.03

XMi

WXGA

MBII6

GB5.4

BRM4

XPHWIT21

318BG

W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.04

XMi

WXGA

MBII6

GB5.4

BRM4

XPHUK1

318BG

UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.04

XMi

WXGA

MBII6

GB5.4

BRM4

XPHWUK2

318BG

1W UMAC

2*512/100/

6L/

5R_bg_0.3

C_AN

AS505

USA/

LX.AV

AS5052WX

ATTL5

N14.1

SO512

N120

NSM8

ABT_

2WXM

Canada -

30J.02

Mi MCECF

WXGA

MBII5

GB5.4

ATH54

Canadian

UMAC

13BG

French

2*512/120/

6L/5R/

CB_bg_0.3

C_AN

157

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

USA/

LX.AV

AS5052WX

ATTL5

N14.1

SO512

N120

NSM8

ABT_

2WXM

Canada -

30J.02

Mi MCEUS

WXGA

MBII5

GB5.4

ATH54

Canadian

UMAC

13BG

French

2*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

ACLA-

LX.AV

AS5052WX

ATTL5

N14.1

SO512

N120

NSM8

ABT_

2WXM

Spanish

30J.02

WXGA

MBII5

GB5.4

ATH54

MCEES1

13BG

UMAC

2*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

ACLA-

LX.AV

AS5051AW

ATMK

N14.1

SO512

N120

NSM8

ABT_

1AWX

Spanish

30J.04

XMi

WXGA

MBII5

GB5.4

BRM4

MCEES1

318BG

UMAC

2*512/120/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Australia/

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NCB2

ABT_

1ANW

New

30C.0

WXCi

WXGA

MBII5

B5.4K

BRM4

XCi

Zealand

LINPUSAU

318BG

1 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N80G

NCB2

ABT_

1AWX

305.04

XCi

WXGA

MBII5

B5.4K

BRM4

XPHMA2

318BG

UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Malaysia

LX.AV

AS5051AN

ATMK

N14.1

SO512

N80G

NCB2

ABT_

1ANW

30C.0

WXCi

WXGA

MBII5

B5.4K

BRM4

XCi

LINPUSMA

318BG

2 UMAC

1*512/80/

6L/5R/

CB_bg_0.3

C_AN

AS505

EMEA

Sweden/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

Finland

30J.04

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCESV5

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/5R/

CB_bg_VP

_0.3C_AN

AS505

EMEA

Slovenia/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

Croatia

30J.05

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCESI1

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/5R/

CB_bg_VP

_0.3C_AN

AS505

EMEA

Holland

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

30J.05

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCENL6

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/5R/

CB_bg_VP

_0.3C_AN

Appendix A

158

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA

Russia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

30J.05

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCERU9

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/5R/

CB_bg_VP

_0.3C_AN

AS505

EMEA

Holland

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

30J.05

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCENL6

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/

5R_bg_VP

_0.3C_AN

AS505

EMEA

Russia

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

1AWX

305.04

XMi

WXGA

MBII6

GB5.4

BRM4

XPHRU2

318BG

UMAC

1*512/100/

6L/

5R_bg_0.3

C_AN

AS505

EMEA

Sweden/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

Finland

30J.05

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCESV5

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/

5R_bg_VP

_0.3C_AN

AS505

EMEA

Slovenia/

LX.AV

AS5051AW

ATMK

N14.1

SO512

N100

NSM8

ABT_

FOX_

1AWX

Croatia

30J.05

XMi

WXGA

MBII6

GB5.4

BRM4

BRM_

VoIP

MCESI1

318BG

2.0

PCMC

UMAC

1*512/100/

BT/6L/

5R_bg_VP

_0.3C_AN

AS505

AAP

Thailand

LX.AV

AS5052N

ATTL5

N14.1

SO512

N120

NSM8

ABT_

FOX_

2NWX

30C.0

WXMi

WXGA

MBII5

GB5.4

BRM4

BRM_

LINPUSTH

318BG

2.0

2 UMAC

1*512/120/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

AAP

Thailand

LX.AV

AS5053WX

ATTL5

N14.1

SO1G

N120

NSM8

ABT_

FOX_

3WXM

30J.05

WXGA

BII6

GB5.4

BRM4

BRM_

MCETH1

318BG

2.0

UMAC

1*1G/120/

BT/6L/5R/

CB_bg_0.3

C_AN

AS505

EMEA

Middle

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

FOX_

1ANW

East

30C.0

WXMi

WXGA

MBII5

B5.4K

BRM4

BRM_

XMi

LINPUSAR

318BG

2.0

9 UMAC

1*512/60/

BT/6L/

5R_bg_0.3

C_AN

AS505

EMEA

Middle

LX.AV

AS5051AN

ATMK

N14.1

SO512

N60G

NSM8

ABT_

FOX_

1ANW

East

30C.0

WXMi

WXGA

MBII5

B5.4K

BRM4

BRM_

XMi

LINPUSAR

318BG

2.0

9 UMAC

1*512/60/

BT/6L/5R/

CB_bg_0.3

C_AN

159

Appendix A

Acer

Wirele

Descriptio

DIMM

HDD 1

Blueto

VOIP

Model

Country

Part

CPU

LCD

ODD

(GB)

oth

Phone

LAN

AS505

EMEA